background image

13

Remote control 
extender does 
not work

• 

To ensure good infrared remote 
control operation, aim your remote 
control at the IR Sensor on the 
receiver and press the buttons 
firmly. ( With some remote controls 
it may be necessary to press and 
hold each button for about a 
second). The working angle of the 
IR Sensor is +/- 15

o

 and the working 

distance is no more than 16.4 feet 
(5m). 

• 

Check the path between the 

transmitter and receiver and clear 

unnecessary obstructions.

• 

Make sure the IR extender is 

pointing toward the sensor 

precisely.

• 

Check the batteries on remote 

control. Replace with new batteries 

if necessary .

• 

The optimum indoor operating 

range is about 49.2 feet (15m).

Important Safety Instructions

•  Keep your A/V signal sender dry and clean. If it gets 

wet or dirty, wipe it dry or clean immediately.

•  Wipe your A/V signal sender with a damp cloth to 

keep it looking new.

•  Use and store your signal sender in room 

temperature environments only.

•  Modifying the A/V signal sender’s internal 

components can cause malfunction and might 

invalidate its warranty. If your A/V signal sender is 

not performing as it should, take it to your local 

RadioShack

 store for assistance.

Specifications

Power Supply.................... ..........................12 V DC/300 mA
Weight (Transmitter/Rceiver)..............................7 oz (200 g)
Dimensions (Transmitter/Receiver)................................. ...... 
..................... 4.7 × 3.9 × 1.7 Inch (12 × 10 × 4.3 cm) (HWD)

Transmitter

Modulation Type (Video and Audio)...............................FM
Operating Frequency ............. 5790, 5828, 5847, 5866 MHz
Output Level................... ....................................................... 
.................. 0 - 10 dBm micro-v/m@3 m (complies with CE)
Input Level....................1.0 Vpp (Audio), 1.0 Vpp (Video)
S-Video Input Level ................................Y:1 Vpp, C:288 mV
Input Impedance......... ..2K Ohm (Audio), 75 Ohm (Video)
Effective Operating Range ................................................... 
......................... Approx. 200 ft (60.96m) (clear line of sight)

15-332 -EN 033110.indd   13

4/6/2010   5:25:17 PM

Summary of Contents for 1500332

















Reviews: