background image

5

RaceAmerica Model 6632E Display Timer

PRODUCT SPECS Model 6632E

 Display Type:  

7-Segment

 Digit Size:   

15” x 7.75

 Number of digits: 

Five

 Dimensions:   

64.6”W x 22.3”H x  4”D

 Mounting:   

Back 3/8-16 PEM nuts

 Housing: 

 

Powder coated aluminum

 View Filter:   

Red Transparent acrylic

 View Range:   

660’ in full sun

 Power Reqt:   

11.8 to 12.6VDC/2A 

 Weight: 

 

38#

 Display Formats: 

ss.fff      99.999 

 

 

 

sss.ff      999.99

 

 

 

mm:ss.f   99:59.9

 

 

 

hh:mm     99:59

PRODUCT SET-UP

Model 6632E Large Display Timer is 

designed to be mounted into or hung from a 

permanent structure. 

RaceAmerica has tried to make use of the 

display timer as simple as possible, however, it is 

strongly suggested that the system be set up in a 

race simulation area without stretching the cables 

all out to gain familiarity with basic operation of 

the components prior to race day.  This can be done 

in a driveway or garage.  Walking through beams 

can simulate vehicles for purposes of familiarizing 

one with basic operation.

STEP 1 - 

Familiarize yourself with the components 

pictured in this manual and how they interconnect.    

The Track Sensor Interconnect Cable is configured 

for connection between the starting line, the 

finish line and the timer.  Several connectors may 

connect different segments of this cable.  The 

cable is keyed to match the start line and finish 

line track sensors, position identified at the track 

sensor end of the cable (Fig.2).  The large round 

connector  connects to the display and the smaller 

connectors (RJ11) connect to the Track Sensors 

at the start line and the finish line as indicated on 

the cable near the RJ11 connector.

The display can be mounted or hung (see 

figure 3). 

STEP 2 - 

Identify the emitter/sensor placement at the 

start line and finish line.  The lane width should be 

set between four (4) and fifty (50) feet (for standard 

5040 Beam Emitters).  Layout the Track Sensor 

Interconnect Cables on the track site as illustrated 

on the Track Sensors/Cabling Diagram  (Fig. 2).

STEP 3 - Connect the Power

Power is supplied to the display and sensors 

through the 12VDC power input. Connecting 

power to the display will set the display into a 

power-up self-test sequence.  Turn on the Beam 

Emitters.

Model 5040 - Infra-red Beam Emitter

Note On/Off switch and placement for four AA 

batteries for each Beam Emitter. Beam Emitters 

are interchangeable with one another.

Model 5140 - Infra-red Track Sensor

Note cable connector is located inside and 

underneath.  Track Sensors are interchangeable 

with one another. 

Fig. 1 - Track Sensors and Emitters

Summary of Contents for 6632E











Reviews: