background image

10

steering trim to neutral and mechanic

ally ce

nter the 

rudder. To do this, loosen the setscrew at the rudder 

secure the rudder pushrod.

NOTICE

signals from other devices and run out of control. 

to the 

E

SC.

CAUTION

: Alwa

y

s k

eep all body parts, hai

r, and loose 

items awa

y f

rom a spinning p

The turn fins on the transom of the boat can be 

adjusted to your preferred style of driving the Velocity.  

For tighter turns, use an appropriately sized wrench 

to loosen the nut and adjust the fins up towards the 

boat.  For wider turns, the fins should be adjusted 

down toward the water.  

Make sure to tighten the nuts after adjustment prior to 

running the Velocity again.  

The trim tabs on the Velocity can be adjusted to modify 

the running attitude of the boat. Turn the trim tab 

adjuster screws clockwise to “push” the bow down into 

the water if the boat “porpoises” or runs with an 

excessive bow-high attitude at full speed. Adjust both 

trim tabs equally and remember that one or two turns 

will make a significant difference in handling! 

Conversely, if the hull feels too “planted” (bow-down), 

adjust the trim tabs anti-clockwise to compensate. 

Always make small changes and test-run to find the 

ideal handling on your specific lake and water 

conditions.   

ropeller as items can 

bec

ome easily e

ntangled.

Boating 

Running Hardware 

Adjustments

Tips

objects, waves, wakes and other r

apidly m

oving 

that come near the surface of the water. You should 

there are people swimming or in park waterwa

y

s and 

to run 

y

our boat.

Y

ou should only dri

ve at maximum speeds when the 

wind.

recommended that 

y

ou look for calm wind and 

responds to 

y

our control.

When making turns, it is suggested that 

y

ou decrease 

Never operate 

y

our boat in less than 3 inches (8cm) of 

water.

6. 

Once 

y

ou care

fully place the bo

at in the water, 

begin driving slo

wly as y

ou become familiar 

is completed b

y turning the 

steering wheel on 

the boat to turn. Begin with small movements 

of the wheel for wider turns and progress to 

sharper turns as 

y

our skills increase.

7. 

Make sure 

y

ou avoid objects in the water at all 

8. 

back to shore or the edge of the pool when it 

begins to lose speed.

9. 

10. 

TIP

: If it 

requires a lot of steering trim on the 

 

Turn fin

Trim tab

Summary of Contents for Velocity 800 BL

















Reviews: