background image

STEALTH-IN-1114

TIME

1           8 HRS

5 SECS          12 MINS

–         +

EVENING

  TIMER

SENS

TIME

1           8 HRS

5 SECS          12 MINS

–         +

EVENING

  TIMER

SENS

TIME

1           8 HRS

5 SECS          12 MINS

–         +

EVENING

  TIMER

SENS

TIME

PHOTOCELL

SENSITIVITY

EVENING TIMER

Sets the time that lights will remain on after the detection zone is vacated. 
Adjustable from approximately 5 seconds to 12 minutes. The factory setting 
is 12 minutes.

For night-only operation, turn the knob completely counterclockwise to (to 
the MOON symbol). For 24-hour operation turn the knob all the way clock-
wise to the MOON/SUN symbol. Adjust counterclockwise to have the sensor 
come on later at dusk, clockwise to have it come on earlier. The Factory 
Setting is Night-only (MOON). If you set Evening Timer while set to 24 hour 
operation Evening Timer will begin immediately after flipping switch.

Increases or decreases the resposiveness and range of the  
sensor (adjustable from 30% to 100%). The Factory Setting is 100%.

The STL360 provides an alternative to normal motion-activated lighting. The 
EVENING TIMER can keep lights on continuously - without motion - for 1 to 
8 hours after dusk. This is great for evening activities requiring continuous 
light. During vacations the EVENING TIMER provides a “lived-in” look by  
simulating an occupant turning lights on at dusk, and then off at bedtime. 

To activate the EVENING TIMER, flip the wall switch controlling the sensor 
three times slowly (off-on-off-on-off-on) within 3 seconds. If you activate 
the EVENING TIMER during daytime, the middle LED should start blinking, 
indicating that the EVENING TIMER will start when dusk is detected. 

Choose the length of time you want continuous lighting. For example, if you 
set the EVENING TIMER to “8”, the sensor will keep lights ON continuosly for 8 
hours after dusk. Once 8 hours have passed, the sensor will revert to motion 
activated mode. At dawn, the photocell will detect light and prevent lights 
from turning on during the daytime.  The Evening Timer Mode will continue 
until you de-activate it. 

If you do not want to use the  
EVENING TIMER, do NOT flip the  
switch 3 times, as described above. 

To de-activate the EVENING TIMER,  
switch the sensor OFF for at least  
10seconds, then ON again. Sensor  
will be in Automatic Mode. (After  
completing the 30 sec warm-up period) 
 
You can affix this label (right),  
provided, to your indoor light  
switch plate for easy referenc

e.

RAB 

STEALTH360

To Keep Lights On: 

Switch off-on-off-on 

within 2 seconds. Resets 

to Auto Mode at dawn. 

To Set 

Evening Timer: 

To keep lights on for 

1-8 hours after dusk, set 

the Evening Timer knob 

on the sensor, then flip 

this switch off-on-off-on 

within 3 seconds. 

To Resume 

Auto Mode: 

Switch off for 10  

seconds, then back on.

Adjusting the Settings

11

12

TIME

1           8 HRS

5 SECS          12 MINS

–         +

EVENING

  TIMER

SENS

Summary of Contents for STEALTH 360













Reviews: