background image

STEALTH-IN-1114

How Does the Super Stealth 360 Work?

The STL360’s infrared sensor “ sees” temperature changes caused by the  
motion of people or cars within its protection zone and turns on lights  
automatically. It welcomes visitors and may deter intruders. 

Total coverage. Two sensors in one.

Two powerful detectors combine to 
give the STL360 “Can’t Miss” Detection: 
180º long forward range (180º x 60’) 
plus superb 360º detection below and 
to all sides.

How do the scanning LED detection indicators work?

Scanning LEDs serve as a  
deterrent by indicating a  
security device in operation. They 
also show the STL360’s mode of 
operation. 

 

Automatic Mode: When the STL360 
is “On Guard” in Auto mode, three 
red LEDs scan  
continuously day and night, except 
during detections  
(at which time the controlled lights 
will go on and LEDs will be off). 

Test Mode

:

 

When the sensor is in 

“Test Mode” all of the LEDs will be 
off.

  

 

Manual Override Mode:

 

When the sensor is ready for  
“Manual Override Mode” the middle 
LED will be on steady. 

 

Evening Timer Mode:

 

When the sensor is ready for “Eve-
ning Timer Mode Mode” the middle 
LED will be blink.

 

TIME

1           8 HRS

5 SECS          12 MINS

–         +

EVENING

  TIMER

SENS

How long do the lights stay on?

Lights remain on as long as there is movement within the  
protection zone. Once the zone is vacated lights can be adjusted to remain 
on approximately 5 seconds up to 12 minutes. Since the lights are on only 
when needed, and the sensor uses only one watt. The Stealth is extremely 
energy efficient.

Can outdoor lights still be turned on with the light switch?

Yes. STL360 can be controlled by a conventional indoor switch or circuit 
breaker. STL360 operates in the auto mode unless changed. Lights can be 
turned on or off manually at night only with the Manual Override Mode.

.

Wall Switch Manual Override: 

(to keep lights on)  

Flip the switch twice slowly (off-on-off-on) within 1–2 seconds.  If you set this 
during the sensor will become “ready” for the Manual Override Mode and will 
start Manual Override at dusk.

Evening Timer:

 

(to keep lights on, and is repeated every night): Flip the 

switch three times slowly (off-on-off-on-off-on) within 1½ – 3 seconds.  You 
can set this during the day and the Evening Timer Mode will begin at dusk.

To Resume Automatic Mode:

Switch power off for at least 10 seconds, then back on. 

Will STL360 detect animals?

 

STL360 may detect large animals. Having animals trigger the sensor can give 
property a “lived-in” look. However, you can limit animal detection by turning 
down the sensitivity knob and/or placing the blinders provided on the lower 
part of the forward lens.

How do you make  

adjustments to the sensor?

Use the adjustment tool  
provided, or a screwdriver with a 1/8” 
wide blade, to adjust the controls 
on the front of the sensor. (see page 
11-12)

 

“On Guard Auto Mode” 

LEDs scan continuously back & forth

      

“Test Mode” all LEDs off

Middle LED on 

steady

 is  

Manual Override Mode

Middle LED 

blinking

 is 

Evening Timer Mode

1

2

Summary of Contents for STEALTH 360













Reviews: