background image

TEX3500LCD

1

 

/ 54

USer Manual

Rev. 2.0 - 27/01/20

 

1.  Preliminary Instructions

• General Warnings

This equipment should only be operated, installed and 

maintained by “trained” or “qualified” personnel who are familiar 

with risks involved in working on electric and electronic circuits. 

“Trained” means personnel who have technical knowledge of 

equipment operation and who are responsible for their own 

safety and that of other unqualified personnel placed under 

their supervision when working on the equipment.   

“Qualified” means personnel who are trained in and 

experienced with equipment operation and who are 

responsible for their own safety and that of other unqualified 

personnel placed under their supervision when working on 

the equipment. 

 WARNING: Residual voltage may be present inside 

the equipment even when the ON/OFF switch is set to 

Off.  Before  servicing  the  equipment,  disconnect  the 

power  cord  or  switch  off  the  main  power  panel  and 

make sure the safety earth connection is connected. 

Some service situations may require inspecting the 

equipment with live circuits. Only trained and qualified 

personnel may work on the equipment live and shall be 

assisted by a trained person who shall keep ready to 

disconnect power supply at need.

R.V.R. Elettronica

  shall not be liable for injury to persons or 

damage to property resulting from improper use or operation 

by trained/untrained and qualified/unqualified persons.

 WARNING: The equipment is not water resistant. 

Any water entering the enclosure might impair proper 

operation. To prevent the risk of electrical shock or 

fire, do not expose this equipment to rain, dripping or 

moisture.

Please observe local codes and fire prevention rules when 

installing and operating this equipment.

  WARNING:  This  equipment  contains  exposed 

live parts involving an electrical shock hazard. Always 

disconnect power supply before removing any covers 

or other parts of the equipment.

Ventilation slits and holes are provided to ensure reliable 

operation and prevent overheating; do not obstruct or 

cover these slits. Do not obstruct the ventilation slits under 

any circumstances. The product must not be incorporated 

in a rack unless adequate ventilation is provided or the 

manufacturer’s instructions are followed closely.

 WARNING: This equipment can radiate 

radiofrequency energy and, if not installed in compliance 

with manual instructions and applicable regulations, 

may cause interference with radio communications.

  WARNING:  This  equipment  is  fitted  with  earth 

connections both in the power cord and for the chassis. 

Make sure both are properly connected.

Operation of this equipment in a residential area may cause 

radio interference, in which case the user may be required 

to take adequate measures.

The specifications and data contained herein are provided 

for information only and are subject to changes without 

prior notice. 

R.V.R. Elettronica

 disclaims all warranties, 

express or implied.While R.V.R. Elettronica attempts to 

provide accurate information, it cannot accept responsibility 

or liability for any errors or inaccuracies in this manual, 

including the products and the software described herein. 

R.V.R. Elettronica 

reserves the right to make changes to 

equipment design and/or specifications and to this manual 

at any time without prior notice.

• Notice concerning product intended purpose and use 

limitations.

This product is a radio transmitter suitable for frequency-

modulation audio radio broadcasting. Its operating 

frequencies are not harmonised in designated user countries. 

Before operating this equipment, user must 

obtain a licence to use radio spectrum from the 

competent authority in the designated user country. 

Operating frequency, transmitter power and other 

characteristics of the transmission system are subject to 

restrictions as specified in the licence.

  2. Warranty

La 

R.V.R. Elettronica 

warrants this product to be free from 

defects in workmanship and its proper operation subject to 

the limitations set forth in the supplied Terms and Conditions. 

Please read the Terms and Conditions carefully, as purchase 

of the product or acceptance of the order acknowledgement 

imply acceptance of the Terms and Conditions. 

For the latest updated terms and conditions, please visit our web 

site at WWW.RVR.IT. The web site may be modified, removed 

or updated for any reason whatsoever without prior notice. 

The warranty will become null and void in the event the 

product enclosure is opened, the product is physically 

damaged, is repaired by unauthorised persons or is used for 

purposes other than its intended use, as well as in the event 

of improper use, unauthorised changes or neglect.     

In the event a defect is found, follow this procedure:
1  Contact the seller or distributor who sold the equipment; 

provide a description of the problem or malfunction for 

the event a quick fix is available.  

Sellers and Distributors can provide the necessary 

information to troubleshoot the most frequently encountered 

problems.  Normally,  Sellers  and  Distributors  can  offer  a 

faster repair service than the Manufacturer would. Please 

note that Sellers can pinpoint problems due to wrong 

installation.
2  If your Seller cannot help you, contact 

R.V.R. 

Elettronica 

and describe the problem; if our staff deems 

it appropriate, you will receive an authorisation to return 

the equipment along with suitable instructions;

3  When you have received the authorisation, you may 

return the unit. Pack the unit carefully before shipment; 

use the original packaging whenever possible and seal 

the package perfectly. The customer bears all risks of 

IMPORTANT

The symbol of lightning inside a triangle placed on the product, evidences the operations for 

which is necessary gave it full attention to avoid risk of electric shocks. 

The symbol of exclamation mark inside a triangle placed on the product, informs the user 

about the presence of instructions inside the manual that accompanies the equipment, im-

portant for the efficacy and the maintenance (repairs).

Summary of Contents for TEX3500LCD































































Reviews: