Qvis 72-8P Series User Manual Download Page 227

Page: 227 / 233

218

6 FAQ

1. Device cannot boot up properly.

These are the following possibilities:



Input power is not correct.



Power connection is not correct.



Power switch button is damaged.



Program upgrade is wrong.



HDD malfunction or something wrong with HDD ribbon.



Front panel error.



Main board is damaged.

2. Device often automatically shuts down or stops running.

These are the following possibilities:



Input voltage is not stable or this is too low.



HDD malfunction or something is wrong with the internal disk.



Button power is not enough.



Front video signal is not stable.



Working environment is too harsh, too much dust.



Hardware malfunction.

3. System cannot detect hard disk.

These are the following possibilities:



HDD is broken.



HDD internal disk is damaged.



HDD cable connection is loose.



Main board SATA port is broken.

4. There is no video output whether this is one-channel, multiple-channel or all-channel

output.

These are the following possibilities:



Program is not compatible. Please upgrade to the latest version.



Brightness is set to the

‘0’ value. Please restore factory default setup.



There is no video input signal or This is too weak.



Check privacy mask setup or your screen saver.



Device hardware malfunctions.

Summary of Contents for 72-8P Series










































































































































































































































Search results

Summary of Contents for 72-8P Series

Reviews:

Qvis 72-8P Series, User Manual, Page: 227 / 233

Search results

Summary of Contents for 72-8P Series

Reviews: