Quonset Microwave QM1014 User Manual Download

Page: 49 / 81

QM1014 LO Synthesizer Distribution Unit

User Manual

4.7 STATus:QUEStionable:ENABle <NRf>

This command sets the enable mask for the questionable event register. A bit value of 1 in the mask will
allow a positive transition in the associated summary bit of the questionable event register if the event bit
transitions to true.

Syntax

STAT

QUES

ENAB

Space

NRf

Allowed Values

The

NRf

parameter can be any integer in the range of 0 to 32767.

Query

:STAT:QUES:ENAB?

The questionable register enable bit mask is queried.

Reset Condition

On reset, the enable bit mask register is cleared.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 0 or greater than 32767, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.2.1

Summary of Contents for QM1014

















































































Search results

Summary of Contents for QM1014

Reviews:

Related manuals for QM1014

Brands by name

Popular brands

Quonset Microwave QM1014, User Manual

Search results

Summary of Contents for QM1014

Reviews:

Related manuals for QM1014

Brands by name

Popular brands