background image

THANK YOU! 

At Quick Play Sport we think sport is all about taking part. We develop innovative products that help 

athletes and coaches at all levels of sport, perform to the best of their ability. If you have any queries or 

suggestions about how we can improve our products, we’d love to hear them. 

Please feel free to get in touch...  [email protected]  /  +44 (0) 114 247 2327

Quick Play Sport Ltd. 1 Longacre Close, Holbrook Industrial Est., Sheffield, S20 3FR, UK 

© 2021 Quick Play Sport Limited. All Rights Reserved. Designed in the UK & USA and made in China to USA & EU standards.

STEP F: ADDING THE MIDDLE POST

2.  With both hands carefully 

lift the top section of the 
System off the Lower 
Post (4) and place on the 
ground: 

3.  Connect the Middle 

Post (15) onto the 
Lower Post (4) and 
locate with  the spring 
buttons: 

4.  Reconnect the top section of 

the System and locate with 
the spring buttons: 

1.  Press the Lower Post 

(4) spring buttons on 
both sides of the pole: 

     

WARNING:

 

Ensure that all 

spring buttons 

are properly 

located before 

play.

  For choosing the QUICKPLAY BALLER MINI HOOP SYSTEM. 

We hope you enjoy and get years of use out of this product. 

If you have any issues, please do not return this product to the 

store. Instead contact us directly: 

 

[email protected] 

We promise to resolve it or your money back.

(NOTE: only complete this step if you intend to use the BMH System on its highest settings) 

8

Summary of Contents for BALLER MINI HOOP SYSTEM









Reviews: