Quell Simline QSP10 Manual Download Page 15

Page: 15 / 21

Trouble shooting:

Problem

Cause and Remedy

The red LED does not

flash very 40s

•

Make sure the product is

activated

Smoke alarm does not

sound when tested

•

Make sure the product is

activated

•

Clean the smoke alarm.

Low battery warning

•

The battery is under low battery

status, please replace the smoke

alarm device.

Fault warning

•

Clean the smoke alarm.

Self-test fault warning

•

Press the TEST button at least 15s,

then release.

False alarm

•

Press the TEST button to silence it.

•

Clean smoke alarm device.

•

Move the smoke alarm device to

new location.

The alarm sounds

different from it is used to

•

Ensure that the battery is not

low voltage.

•

Clean smoke alarm.

•

If the unit is out of warranty, please replace with another

new alarm.

Summary of Contents for Simline QSP10






















Search results

Summary of Contents for Simline QSP10

Reviews:

Related manuals for Simline QSP10

Brands by name

Popular brands

Quell Simline QSP10, Manual

Search results

Summary of Contents for Simline QSP10

Reviews:

Related manuals for Simline QSP10

Brands by name

Popular brands