Quectel M50 Hardware Design Download Page 45

Page: 45 / 89

M50 Hardware Design

M50_HD_V2.0

- 45 -

UART Port with hardware flow control is shown as below. This connection will enhance the

reliability of the mass data communication.

RTS

CTS

RTS

CTS

GND

RXD

TXD

RXD

GND

Module (DCE)

Host (DTE)

Controller

Figure 20

: Reference design for UART Port with hardware flow control

3.9.1.3. Firmware upgrade

The TXD, RXD can be used to upgrade firmware. The PWRKEY pin must be pulled down before

the firmware upgrade. Please refer to the following figure for Firmware upgrade.

IO Connector

TXD

RXD

GND

PWRKEY

Module (DCE)

UART port

TXD

RXD

GND

PWRKEY

Figure 21

: Reference design for Firmware upgrade

Note: The firmware of module might need to be upgraded due to certain reasons, it is

recommended to reserve these pins in the host board for firmware upgrade. For detailed design,

please refer to the document [11].

Quecctel

Confidential

Summary of Contents for M50


























































































Search results

Summary of Contents for M50

Reviews:

Related manuals for M50

Brands by name

Popular brands

Quectel M50, Hardware Design

Search results

Summary of Contents for M50

Reviews:

Related manuals for M50

Brands by name

Popular brands