background image

                                                                                                                                             

LTE  Module  Series 

                                                                                                  EG25-G  Hardware  Design

 

 

EG25-G_Hardware_Design                                                                                                                      51 / 100 
 

 

 

 

 

It  is  important  to  route  the  SDIO  signal  traces  with  total  grounding.  The  impedance  of  SDIO  data 
trace is 50Ω (±10%).   

 

Make sure the adjacent trace spacing is two times of the trace width and the load capacitance of 
SDIO bus should be less than 15pF.   

 

It is recommended to keep the trace length difference between CLK and DATA/CMD less than 1mm 
and the total routing length less than 50mm. The total trace length inside the module is 27mm, so the 
exterior total trace length should be less than 23mm. 

 

3.14. 

Wireless Connectivity Interfaces 

 
EG25-G supports a low-power SDIO 3.0 interface for WLAN and a UART/PCM interface for BT. 

 

The following table shows the pin definition of wireless connectivity interfaces. 
 

Table 16: Pin Definition of Wireless Connectivity Interfaces 

Pin Name 

Pin No.  I/O 

Description   

Comment 

WLAN Part 

SDC1_DATA3 

129 

IO 

WLAN SDIO data bus D3 

1.8V power domain 

SDC1_DATA2 

130 

IO 

WLAN SDIO data bus D2 

1.8V power domain 

SDC1_DATA1 

131 

IO 

WLAN SDIO data bus D1 

1.8V power domain 

SDC1_DATA0 

132 

IO 

WLAN SDIO data bus D0 

1.8V power domain 

SDC1_CLK 

133 

DO 

WLAN SDIO bus clock 

1.8V power domain 

SDC1_CMD 

134 

IO 

WLAN SDIO bus command 

1.8V power domain       

WLAN_EN 

136 

DO 

WLAN function control via FC20 
module.   

1.8V power domain 
Active high. 
Cannot be pulled up before 
startup. 

Coexistence and Control Part 

WLAN_SLP_CLK  118 

DO 

WLAN sleep clock 

 

PM_ENABLE 

127 

DO 

WLAN power control.   

1.8V power domain 
Active high. 

WAKE_ON_ 
WIRELESS 

135 

DI 

Wake up the host (EG25-G 
module) by FC20 module. 

1.8V power domain 

Summary of Contents for EG25-G








































































































Reviews: