QUATRO
Air Technologies Inc.
------------------------------------------------------------
We Make Clean Air
----------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: (514) 630-4444 Fax: (514) 630-4454 website:
1- INTRODUCTION
You are now the owner of a
QUATRO CSA System
, an advanced effective indoor dust and fume collection system designed
specifically to remove particulate matter and odor causing gas phase contaminants at the source. You can expect a
noticeable improvement in air quality as the
CSA System
begins the process of reducing microscopic airborne particulate.
The
CSA System
normally features 4 stages of filtration:
1) An Anti-Microbial Filter Bag that serves as the pre filter. This captures large debris.
2) A High Capacity intermediate filter for larger particles.
3) A HEPA filter captures & holds fine particles protecting the motor and ensuring a clean output.
4) A Chemical Filter to absorb & contain odor causing gas phase contaminants.
The filter sequence can be customized to your application. Contact Quatro Air for more info.
WARNING
–
To reduce the risk of damage to your system read and follow all instructions. Failure to follow these
guidelines may result in undesired operation or damage that will not be covered under warranty.
2-
WHAT’S IN THE BOX
Models
Name
Accessories
CSA626L
CSA625L
CSA6B6
CSA6B5
CSA600 120V
c/w “Long Life” Motors
CSA600 230V
c/w “Long Life” Motors
CSA600 120V
c/w “Brushless” Motor
CSA600 230V
c/w “Brushless” Motor
(1) O&M Manual (1) Power Cord
(1) Appropriate Size Inlet Plate
(2) Clamps (No Clamps For 1.5”)
(1) Piece Of The Appropriate Size Hose (Per Inlet)
(1) Remote Cable (AE427) Only For Units Equipped With
DB9 Remote Connector
3- IMPORTANT SAFETY & INSTALLATION PRECAUTIONS
- Ensure to use proper voltage as indicated on the system.
- To reduce the risk of electric shock, do not expose to excessive moisture, water or rain.
- Use only on a grounded electrical circuit.
- Do not install or operate the system in an enclosed space or against a wall. Unit may overheat & shut down.
- Keep all objects at le
ast 6” away from the casing, especially the discharge grill.
- All filters must be in place whenever this machine is in operation.
- ALWAYS turn system on/off switch to off and disconnect power prior to accessing unit, replacing filters, or servicing motor(s).
- Allow the unit to cool for 45 minutes before performing any service to the motor(s).
- Do not kink hose or restrict airflow in any way.
SAVE THESE INSTRUCTION FOR FUTURE REFERENCE
Failure to follow these guidelines may result in undesired operation or damage, not covered under this warranty.
4- INSTALLATION
1) Install the unit in the chosen location.
2) Open the filter access door & lid
and install the filters in the correct order. See the “Filter Service & Replacement”
section for more info.
3) Connect the supplied hose from the Quatro System to the Laser/Printer.
4) Connect the power cord to the unit and then to the power source.
VERIFY VOLTAGE BEFORE CONNECTING.
- ONLY USE THE POWER CORD SUPPLIED WITH THE EQUIPMENT.
- Always plug the unit directly into the wall outlet. Do not use extension cords or power bars.
-
Ideally the unit should be plugged into it’s own dedicated circuit.
- The system is designed to be constantly powered (plugged in). The system will not function correctly and may get
damaged if power source is used to control the operation. See “Controls” for more info.
5) Turn unit on & adjust the desired airflow using the arrow up and down keys. Set airflow to lowest acceptable level to
properly evacuate your equipment.
For information abou
t remote operation see the “Controls” section.
WARNING: DO NOT OPERATE UNIT UNLESS ALL FILTERS ARE IN PLACE.
Important Notes:
NONE of the filters in the system are cleanable. They will all need to be removed and disposed of periodically.
See t
he “Filter Service & Replacement” Section for more info.
