Quantum Quantum 610 Owner'S Manual Download | Manualshive

Page: 35 / 55

background image

Quantum 610

www.quantumrehab.com

35

V I I . O P E R A T I O N

Actuator Keys and Actuator Lights (For Optional Equipment)

Actuator keys and actuator lights are used for optional equipment such as power elevating leg rests. For specific operation
of the actuator keys and actuator lights, contact your Quantum Rehab Specialist.

Horn Key

The horn key activates the horn.

Locking/Unlocking the VSI

The VSI has a feature that enables you to lock your power chair to prevent unauthorised use.

To lock the VSI:
1. With the VSI switched on, press and hold the on/off key. After 1 second, the VSI should beep.
2. Release the on/off key.
3. Push the joystick to the full forward position until the VSI beeps.
4. Pull the joystick to the full rearward position until the VSI beeps.
5. Release the joystick. There should be a long beep.
6. The VSI is now locked.

To unlock the VSI:
1. Press the on/off key and power on the VSI. The maximum speed/profile indicator should ripple up and down.
2. Push the joystick to the full forward position until the VSI beeps.
3. Pull the joystick to the full rearward position until the VSI beeps.
4. Release the joystick. There should be a long beep.
5. The VSI is now unlocked.

NOTE: If the above procedure fails to either lock or unlock the VSI, contact your Quantum Rehab Specialist.

Off-board Charger/Programming Socket

The off-board charger/programming socket is located on the front of the VSI. If you use an off-board charger, the charger
current should not exceed 8 amps. Contact your Quantum Rehab Specialist for more information.

WARNING! Only chargers with Neutrik NC3MX plugs should be connected to the off-board charger/

programming socket. See your Quantum Rehab Specialist for more information.

NOTE: The socket may also be used for reprogramming the VSI. Contact your Quantum Rehab Specialist for
more information.

Motor Connectors

This connects the VSI to the power chair’s motors and motor brakes.

Controller Connector

This connects the VSI to the power chair’s batteries, motors, and motor brakes.

Battery Connector

This connects the VSI to the power chair’s batteries.

Actuator Connector (Optional)

This connects the VSI to the power seat actuator.

«
...
33
34
35
36
37
...
»

Summary of Contents for Quantum 610
























































Reviews:

No comments

Related manuals for Quantum 610

Brand: Otto Bock Pages: 72

Brand: EZee Life Pages: 27

Syst'am Polyair

Brand: SUMED Pages: 2

Brand: DELTA-SPORT Pages: 22

Brand: Etac Pages: 48

Brand: Otto Bock Pages: 56

Brand: Otto Bock Pages: 48

Brand: Handicare Pages: 4

Brand: PaceSaver Pages: 49

Brand: AAT Pages: 32

Freedom Gold Series

Brand: Miracle Mobility Pages: 44

ViCare UNIVERSAL 921704 68

Brand: Villeroy & Boch Pages: 4

Occupant Restraints

Brand: Unwin Pages: 24

Brand: Travel Buggy Pages: 54

Brand: SHONAQUIP Pages: 14

Brand: Mobiak Pages: 19

Brand: Mobiak Pages: 20

Brand: Mobiak Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands