980 User Guide
– HDMI HDCP 2.2 Compliance
Rev. A2
Page 20
October 15, 2014
3.4
Setting the +5V levels
The 980 enables you to view the +5V levels from the source device under test and to set the current load on the
+5V lead.
1. Select the
RX 5 Volts…
item from the
Instrument
pull-down menu on the built-in front panel as shown below.
The RX 5V Status/Configuration dialog box is displayed as shown below.
2. Note the current Measured 5V level (4.98 in the example above).
3. Select the Threshold Level using the upper slidebar (0.0 to 5.3V). Be sure to select the
Apply
button. Then hit
Refresh
to view the new value. You may wish to lower the threshold to enable testing of a source whose 5V
level is too low. If you specify a threshold higher than the voltage detected there will be no effect on the ability
to test.
4. Select the current Load using the lower slidebar provided. Increasing the current load will cause the detected
voltage to fall. Be sure to select the
Apply
button. Then hit
Refresh
to view the new value.
3.5
Enabling HDCP 2.2
The 980 Protocol Analyzer module has to be configured to respond to HDCP 2.2 authentication from a source. Use
the following procedure to enable HDPC 2.2 authentication in the 980 Protocol Analyzer module. You can enable
HDCP 2.2 on the Protocol Analyzer receiver either through the embedded 980 GUI or the external 980 GUI. The
following procedures assume you are using the external GUI but exceptions are provided instructing you how to
enable HDCP 2.2 through the embedded GUI.
1. From the
Card Control
window, select
Receiver
. Refer to the screen example below.
Summary of Contents for 980
