background image

10/08

Page  7

Quadra-Fire  •  Hudson Bay  •  7003-121 Rev. i

3

Appliance Location and Clearances

A. Selecting Appliance Location

NOTE: 

·  

Illustrations refl ect typical installations and are FOR  

DESIGN PURPOSES ONLY.

·

    Illustrations/diagrams are not drawn to scale.

·

   Actual installation may vary due to individual design    

preference.

When selecting a location for your appliance it is important to 
consider the required clearances to walls (see 

Figure 3.1

).  

WARNING

Fire Risk
Provide adequate clearance:
•  Around air openings
• To 

combustibles

• For 

service 

access

Locate appliance away from traffi c areas.

Fire Risk.

  Locate and install appliance to all 

clearance specifi cations in manual.

WARNING

B. Clearances 

Figure 3.1   

NOTE:

 Flooring beneath appliance may reach 90 degrees 

plus room ambient temperature. Check with flooring 
manufacturer for maximum temperature allowed on flooring 
surfaces.

It is permissible to place the appliance on carpet.

CAUTION

Some carpet materials may be sensitive to radiant heat from the 
appliance causing discoloration or odor.

Fire Risk. 
Odor Risk.
Tipping Risk
•  Install appliance on a stable, level platform/

fl oor strong enough to support appliance 
without tipping. 

• USE 

wood 

fl ooring, ceramic tile, brick hearth 

or high pressure laminate fl ooring applied 
directly over the sub-fl ooring material.

WARNING

NOTE:  For actual appliance dimensions refer to Sec-
tion 12.

Model

A

B

C

D

E

F

G

H

Hudson Bay

Inches 

9-5/8

1

36

46-1/2

9

4

54

21

Millimeters

219

25

91

118

229

102

137

533

G

H

A

A

B

C

E

D

E

F

F

Summary of Contents for Hudson Bay Direct Vent Gas Appliance...


















































Reviews: