background image

November 7, 2014 

 

 

 

           7061-197D 

 

 

 

         

                  11

Explorer II Medium Wood Stove

Chimney Systems

NOTE: I

n Canada when using a factory-built chimney it must 

be safety listed,

 Type UL103 HT (2100

o

F) CLASS “A” 

or 

conforming to 

CAN/ULC-S629M, STANDARD FOR 650

o

FACTORY-BUILT CHIMNEYS.

Floor
Protector

Chimney
Connector

Insulated " T "

Flashing

Listed Termination Cap

Trim Collar on
Inside Wall

Listed Chimney

Storm Collar

Wall Support

Roof Brace (if required)

Thimble

Chimney
Connector

Ceiling Support

Listed Chimney

Listed Termination Cap

Storm Collar

Flashing

Figure 11.1 Prefabricated Exterior Chimney

Figure 11.2 - Prefabricated Interior Chimney

A.  Venting Components 

Chimney Connector:

It is also known as fl ue pipe or stove pipe.  The chimney 
connector joins the stove to the chimney.  It must be a 6 inch 
(152mm) minimum diameter 24 gauge mild steel black or 26 
gauge blued steel, or an approved air-insulated double wall 
venting pipe.  

Thimble

:  

A manufactured or site-constructed device installed in 
combustible walls through which the chimney connector 
passes to the chimney.  It is intended to keep the walls 
from igniting.  Site constructed thimbles must meet NFPA 
211 Standards.  Prefabricated must be suitable for use with 
selected chimney and meet UL103 Type HT Standards.  Follow 
instructions provided by the manufacturer for manufactured 
thimbles for masonry chimney and prefabricated chimneys.

Chimney

:

The chimney can be new or existing, masonry or prefabricated 
and must meet the following minimum requirements specifi ed 
in Section 5B.

B.  Chimney Systems

Prefabricated Metal Chimney

• 

Must be minimum 6 inch (152mm) diameter (ID) high 

temperature chimney listed to UL 103 HT (2100

o

F) or 

ULC S629M.

• 

Must use components required by the manufacturer 

for installation.

• 

Must maintain clearances required by the manufacturer 

for installation.

• 

Refer to manufacturers instructions for installation.

Summary of Contents for Explorer II Medium





















Reviews: