background image

November 7, 2014 

 

 

 

           7061-197D 

 

 

 

         

                  13

Explorer II Medium Wood Stove

Chimney Height / Rise and Run

This product was designed for and tested on a 6 inch (152mm) 
chimney, 14 to 16 feet (420-480cm) high, (includes stove 
height) measured from the base of the appliance.  The further 
your stack height or diameter varies from this confi guration,  
the greater the likelihood it may affect performance. 

Chimney height may need to be increased by 2  - 3% per 
each 1000 feet above sea level.  It is not recommended to 
use offsets or elbows at altitudes above 4000 feet above sea 
level or when there are other factors that affect fl ue draft.

C. Installing Chimney Components

Chimney Connector

Single wall connector or stove pipe.  

This must be at least 24 gauge mild steel or 26 gauge blue 
steel.  The sections must be attached to the appliance and to 
each other with the crimped (male) end pointing toward the 
stove.  All joints, including the connection at the fl ue collar, 
should be secured with 3 sheet metal screws.  Make sure 
to follow the minimum clearances to combustibles.   Where 
passage through the wall, or partition of combustible con-
struction is desired in Canada, the installation shall conform 
to CAN/CSA-B365.

Factory-built listed chimney connector (vented).

A listed connector (vented) must be used when installing this 
unit in a mobile home.  The listed connectors must conform 
to each other to ensure a proper fi t and seal.

Flue Gas

Direction

Crimped

End

Toward

Stove

Secure pipe sections with a

minimum of 3 screws

Figure 13.2   Chimney Connector  (Stove Pipe)

WARNING

Asphyxiation Risk.

•  DO NOT CONNECT THIS UNIT TO A CHIMNEY 

FLUE SERVICING ANOTHER APPLIANCE.

•  DO NOT CONNECT TO ANY AIR DISTRIBUTION 

DUCT OR SYSTEM.

May allow fl ue gases to enter the house.

Improper installation, adjustment, alteration, service or main-
tenance can cause injury or property damage. Refer to the 
owner’s information manual provided with this appliance. For 
assistance or additional information consult a qualifi ed installer, 
service agency or your dealer.

WARNING

Fire Risk

.

Inspection of Chimney:

•    Chimney must be in good condition.

•    Meets minimum standard of NFPA 211

•  Factory-built chimney must be 6 inch (152mm) UL103 HT.

WARNING

WARNING

ONLY use connector:

•  Within the room, between appliance and ceiling or wall.
Connector shall NOT pass through:
•  Attic or roof space
•  Closet or similar concealed space
•  Floor or ceiling

Maintain minimum clearances to combustibles

Fire Risk.

Follow Chimney Connector Manufacturer’s 
Instructions for Proper Installation.

Chimney Flue

Liner

Fireclay

Liner or

Equivalent

Masonry Chimney

Constructed to NFPA 211

Wall Spacer

Wall Band

Trim Collar

Chimney

 Connector

1 inch (25mm) Air

Space to Chimney

Section

Min. Clearance

2 inch (51mm)

Min. Chimney Clearance to

Wall Spacer and

Combustibles - 2 inch (51mm)

Chimney Section

Figure 13.1

Solid Pack Chimney with Metal Supports as a Thimble 
(Cont’d)

Summary of Contents for Explorer II Medium





















Reviews: