background image

 8 

 

 

 

 

                      

7061-197D 

 

 

 

         November 7, 2014

Explorer II Medium Wood Stove

B. Clearances to Combustibles

BACKWALL / SIDEWALL 

A

B

C

C

CORNER INSTALLATION

B

ALCOVE TOP VIEW 

D

A

ALCOVE SIDE VIEW

NOTE:  Clearances may only be reduced by means 
approved by the regulatory authority having jurisdiction

Fire Risk.

•  Comply with all minimum clearances to 

combustibles as specifi ed.

•  Failure to comply may cause house fi re.

WARNING

 

A B C 

INSTALLATION: FULL VERTICAL OR ALCOVE

SINGLE WALL PIPE

DOUBLE WALL PIPE  

Explorer II 

 

 

9.38 (238) 

         20.25 (514)          10.5 (267) 

55 (1397)

 

  * FOLLOW PIPE MANUFACTURES CLEARANCES AS REQUIRED

 

Explorer II 

 

 

10.5 (267) 

         20.25 (514)          13.5 (343) 

55 (1397)

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS in inches & (Millimeters)

NOTE: All A, B, and C Dimensions are to the center of the flue collar

For alcove only: 

Six inch diameter listed Double wall air insulated connector 

pipe with UL103 HT listed factory built Class A chimney or masonry chimney. 

Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a 

minimum height of 48 inches (1220mm) to top of unit and the referenced 

clearances. Canada must comply with CAN/ULC-S269 M87 for the 650° factory 

built chimney

 

STOVE TO CEILING 
CLEARANCE 

*

12

(305)

20.25
(514)

50

(1270)

MANTEL
12” MAX

HORIZONTAL THROUGH WALL 
TOP AND SIDE VIEW

Summary of Contents for Explorer II Medium





















Reviews: