background image

 18 

 

 

 

 

                      

7061-197D 

 

 

 

         November 7, 2014

Explorer II Medium Wood Stove

CAUTION

THE STRUCTURAL INTEGRITY OF THE MOBILE HOME 
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED

Do NOT cut through:
•  Floor joist, wall, studs or ceiling trusses.
•  Any supporting material that would affect the structural integ-

rity.

Asphyxiation Risk. 

NEVER INSTALL IN A SLEEPING ROOM.

Consumes oxygen in the room.

WARNING

You must use a Quadra-Fire Outside Air Kit Part 
OAK-ACC for installation in a mobile home.

1.  An outside air inlet must be provided for combustion.

2.  Appliance must be secured to the mobile home structure 

by bolting the legs to the fl oor.  

3.  Appliance must be grounded with #8 solid copper 

grounding wire or equivalent and terminated at each end 
with N.E.C. approved grounding device.

4.  Appliance must be installed with an approved UL103 HT 

ventilated chimney connector, UL103 HT chimney, and 
terminal cap with spark arrestor.  Never use a single wall 
connector (stove pipe) in a mobile home installation.  Use 
only double-wall connector pipe, Dura-Vent DVL, Selkirk 
metalbestos DS or Security DL double-wall connector or 
any listed double-wall connector pipe.

5.  In Canada, this appliance must be connected to a 6 inch 

(152mm) factory-built chimney conforming to CAN/ULC-
629M, STANDARD FOR FACTORY BUILT CHIMNEYS. 

6.  Follow the chimney and chimney connector manufacturer’s 

instructions when installing the fl ue system for use in a 
mobile home.

7.  Maintain clearance to combustibles.

8.  Floor protection requirements must be followed precisely.

9.  Use silicone to create an effective vapor barrier at the 

location where the chimney or other component penetrates 
to the exterior of the structure.

NOTE:

  Offsets from the vertical, not exceeding 45°, are 

allowed per Section 905(a) of the Uniform Mechanical Code 
(UMC). Offsets greater than 45° are considered horizontal and 
are also allowed, providing the horizontal run does not exceed 
75% of the vertical height of the vent. Construction, clearance 
and termination must be in compliance with the UMC Table 
9C. This installation must also comply with NFPA 211.

NOTE:

 Top sections of chimney must be removable to allow 

maximum clearance of 13.5 feet (411cm) from ground level 
for transportation purposes.

10.  Burn wood only.  Other types of fuels may generate 

poisonous gases (e.g., carbon monoxide).

11.  If unit burns poorly while an exhaust blower is on in home, 

(i.e., range hood), increase combustion air.

12.  Installation shall be in accordance with the Manufacturers 

Home & Safety Standard (HUD) CFR 3280, Part 24.

Approved for USA Installation only!

Mobile Home Installation

Summary of Contents for Explorer II Medium





















Reviews: