Quadra-Fire 41I-ACC User Manual Download Page 21

October 14, 2013 

 

 

 

           7045-910 

 

 

 

         

                  21

41I-ACC

DOUBLE-SIDED

T

APE

DOUBLE-SIDED

T

APE

SCREWS ARE CIRCLED

EXPLODED VIEW OF SCISSORS

Figure 21.1

Thermal 

Protection

Decorative tile may 

be installed

INSTALL FRONT TRIM LAST.

CORNERS OVERLAP SIDE 

TRIM PIECES

EXPAND SCISSORS TO DESIRED HEIGHT

CUT TOP EDGE OF TRIM, 

NOT BOTTOM EDGE

Figure 21.2

Figure 21.3

Figure 21.4

Part No.  841-0990, size 9” x 45” and 

Part No. ADJSPT-12, size 12” x 50”

G.  Zero Clearance Adjustable Trim Support,  

     2” to 10” 

Included in Kit: (

1)  Trim  Top,  (1)  Trim  Front,  (2)  Trim 

Sides, Double-Sided Tape (already installed)

Tools Needed: 

 

Phillips  Head  Screwdriver,  Sheet  Metal 

Shears, Measuring Tape, Gloves

1. The  10  screws  on  each  set  of  scissors  will  already  be 

loose when shipped.  

Figure 21.1.

2.    Expand  scissors  to  desired  height.   Tighten  screws  to 

hold  in  place  using  Phillips  Head  screwdriver. 

Figure 

21.2.

3.  Measure front and side trims to required height to cover  

scissors and mark pieces for cutting.  Cut excess mate-

rial from top

 of trims edge, not  bottom.  This edge will 

be sharp; wear gloves to prevent injury to your hands.  

Figure 21.2.

4.  Using sheet metal shears, cut trim along the marked 

edge.  The cut edge fits under lip of top trim, so it allows 

for some variance in your straight edge.  

5. The double-sided tape that holds front and side trims to  

scissors has a particularly powerful bonding adhesive.  

Adjustments are extremely difficult once trim has adhered 

to tape.  Do a dry run first without removing paper from 

tape.

6.  Place cut edge of trim under top lip and into position on 

scissors.  Place side pieces on first and then front piece.  

The front piece overlaps side pieces. 

 

NOTE:  The trim in 

the Flush Mount Kit is one piece.

7.  Once you are satisfied with the positioning, remove trim 

and set aside.

8.  Remove the paper from double-sided tape that is to 

accept trim side.  Align side and then press hard against 

tape to secure side piece.  Repeat for other side.  Install 

front trim piece last.

9.  

There are 3 holes in the back flange of the top to secure it 

to the wall if necessary.  Use the appropriate fastener for 

the type of wall material, i.e., brick, sheetrock, etc.

 

NOTE:  3/8” ( 9.5mm) 

thick tile or like material can be cut 

to size and fit under lip of  top trim edge for a decorative 

touch.  

Figure 21.3.

10. Thermal protection of 1-1/2 inches (38mm), “k” value of 0.49 

and R value of 3.06 under the zero-clearance trim support.  

Figure 21.4.

Summary of Contents for 41I-ACC

























Reviews: