Quadivator PB60 06 Assembly/Operators/Parts Manual Download Page 2

                     QUADIVATOR WARRANTY POLICY

The warranty for the Quadivator Product is a limited warranty.

The manufacturer’s warranty to the original customer is - the product is free from defects in 
materials and workmanship for a period of one (1) year from the date of purchase by the 
original purchaser.

We will repair or replace, at our discretion, parts found to be defective due to materials and 
workmanship.

The warranty is subject to the following limitations and exclusions:

1. Engine Warranty

 - all engines utilized on our products have a separate warranty 

extended to them by the engine manufacturer.  Any engine service difficulty is the 
responsibility of the engine manufacturer and in no way is Quadivator Inc. or its agents 
responsible for the engine warranty.  The Briggs & Stratton Engine Service Hot Line is 1-
800-233-3723.

2. Commercial Use -

 the warranty period for any product used for commercial or rental use 

is limited to ninety (90) days from the date of original purchase.

3. Limitations -

 the warranty applies only to products which have been properly assembled, 

adjusted and operated in accordance with the instructions contained within this manual.  
The warranty does not apply to any product of Quadivator Inc. that has been subject to 
alteration, misuse, abuse, improper assembly or installation, shipping damage or normal 
wear of the product.

4. Exclusions -

 excluded from this warranty are normal wear, normal adjustments and 

normal maintenance.

In the event you have a claim under this warranty, you must return the product to an 
authorized service dealer.  All transportation charges, damage or loss incurred during 
transportation of parts submitted for replacement or repair under this warranty shall be 
borne by the purchaser.  Should you have any questions concerning this warranty, please 
contact us toll-free at 866 770-2169 or on our web-site at www. quadivator.com.  The 
model, serial numbers, date of purchase and the name of the authorized Quadivator dealer 
from whom you purchased the Quadivator Product will be needed before any warranty 
claim can be processed.

This warranty does not apply to any incidental or consequential damages and any implied 
warranties are limited to the same time periods stated for all expressed warranties.  Some 
provinces and states do not allow the limitation of consequential damages or limitations on 
how long an implied warranty may last, so the above limitations may not apply to you.  This 
warranty gives you specific legal rights and you may have other rights, which vary from 
province to province or state to state.  

This is a limited warranty as defined by the Magnuson-Moss Act of 1975.

Summary of Contents for PB60 06





























Reviews: