Quaddrix QT-500-16 User Manual Download Page 7

Page: 7 / 128

Chapter 2 Installation

Warning: Before you install the Hard Disks, please make sure the
power of DVR is switched off.

2.1 HDD Installation

Installation notice

The DVR by factory default has not HDD installed. Based on the record
schedule, you can calculate the total capacity you need (refer to Appendix
A).

HDD installation

Open the DVR box.

If you want to install 2 HDD for one IDE interface, please set master
and slave HDD (set the jumpers properly in the HD). If you want to
install 4 HDD, please remove CD-R/W mount bracket.

Place the HDD on the soleplate and fix it with screw.

Connect the ATA data cable correctly. The cable has three
connectors for DVR main board, master HDD and slaver HDD.

Plug the HDD power connector.

Cover and fix the DVR box.

Note: After you install the HDD, you must format them. Please refer to
section 6.4.

Summary of Contents for QT-500-16

































































































































Search results

Summary of Contents for QT-500-16

Reviews:

Related manuals for QT-500-16

Brands by name

Popular brands

Quaddrix QT-500-16, User Manual

Search results

Summary of Contents for QT-500-16

Reviews:

Related manuals for QT-500-16

Brands by name

Popular brands