Quaddrix QT-500-16 User Manual Download Page 31 | Manualshive

Page: 31 / 128

background image

motion detection recording). Red means network transmission. Orange
means both recording and network transmission.

Start/Stop:

“

9

” means you can start corresponding channel recording.

“×” means you can stop recording.

Start All:

Press this button to start all channels recording.

Stop All:

Press this button to stop all channel recording.

Exit manual record

Press [ESC] key to enter into preview mode. Press [MENU] key to enter
into main menu. Press [PLAY] key to enter into playback menu. Press
[PTZ] key to enter into PTZ control mode.

4.6 Playback

Note: The user must have “Playback” right.

Playback interface

In preview mode, press [PLAY] key, in the pop-up login dialog, select
username and input correct password, you can enter into “Playback”
interface.
In menu mode, press [PLAY] key, you can enter into “Playback” interface
directly.

«
...
29
30
31
32
33
...
»

Summary of Contents for QT-500-16

































































































































Reviews:

No comments

Related manuals for QT-500-16

Brand: Q-See Pages: 6

Brand: Triax Pages: 36

Brand: Prestigio Pages: 42

Brand: Car Solutions Pages: 13

Brand: Timespace Pages: 185

Brand: Darim Pages: 4

Brand: HIKVISION Pages: 93

Brand: Plantron Pages: 48

Brand: Clinton Electronics Pages: 30

Brand: Vicon Pages: 50

Brand: Vicon Pages: 90

Brand: VC Pages: 96

Brand: L3 Mobile-Vision Pages: 280

Brand: WBOX Technologies Pages: 283

Brand: EverFocus Pages: 162

Brand: Steren Pages: 35

Brand: CONCORD Pages: 120

Brand: StreetWise Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands