background image

3

 

 

 

Maintenance and Repair

 

WARNING!: 

Advanced technology, e.g., the use of modern materials and powerful electronics, requires 

specially adapted maintenance and repair methods. To avoid a danger of subsequent damage to the 
apparatus, injuries to persons and/or the creation of additional safety hazards, all maintenance or repair 
work on the apparatus should be performed only by a Zykronix authorized service station or an authorized 
Zykronix International Distributor. Zykronix is not responsible for any injury, harm or related damages 
arising from any failure of the customer, owner or user of the apparatus to facilitate those repairs.

 

 

FCC Statement

 

This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions:

 

1.

 This device may not cause harmful interference, and

 

2.

 This device must accept any interference received including interference that cause undesired operation.

 

 

NOTE: 

This equipment has been tested and found to comply with the limits for a Class B digital device, 

pursuant to Part 15 of the FCC Rules.

 

 

These limits are designed to provide reasonable protection against harmful interference in a residential installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance 
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to 
correct the interference by one or more of the following measures:

 

    EN 

 

  Reorient or relocate the receiving antenna.

 

  Increase the separation between the equipment and receiver.

 

  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

  Consult the dealer or an experienced radio/TV technician for help.

 

 

IC Statement

 

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two 
conditions:

 

1.

 This device may not cause harmful interference, and

 

2.

 This device must accept any interference received, including interference that may cause undesired operation.

 

Le présent appareil est conforme aux CNR 

d’Industrie Canada applicables aux appareils radio exempts de licence. 

L’exploitation est autorisée aux deux conditions suivantes :

 

1.

 

l’appareil ne doit pas produire de brouillage;

 

2.

 

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 
susceptible d’en compromettre le fonctionnement.

 

Summary of Contents for TSC-7t











Reviews: