QED Hammerhead Pro Field Service Manual Download Page 17

O

Terms, Conditions, and Warranty

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED OR STATUTORY (INCLUDING 

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITYAND FITNESS FOR A PARTICULAR PURPOSE), WHICH 

OTHER WARRANTIESARE EXPRESSLY EXCLUDED HEREBY

, and of any other obligations or liabilities on the part of QED, and QED 

neither assumes nor authorizes any person to assume for it any other obligation or liability in connection with said products, materials 

and/or workmanship. It is understood and agreed that QED shall in no event be liable for incidental or consequential damages resulting 

from its breach of any of the terms of this agreement, nor for special damages, nor for improper selection of any product described or 

referred to for a particular application.

This warranty will be void in the event of unauthorized disassembly of component assemblies. Defects in any equipment that result from 

abuse, operation in any manner outside the recommended specifications,  procedures, use and applications other than for intended use, 

or exposure to chemical or physical environment beyond the designated limits of materials and construction will also void this warranty.

Chemical attack of liquid contacting equipment and supplies shall not be covered by this warranty. A range of materials is available from 

QED and it is the Buyer's responsibility to select materials to fit the Buyer's application. QED will only warrant that the supplied liquid 

contacting materials will conform to published QED specifications and generally accepted standards for that particular  material.

ILLUSTRATIONS AND DRAWINGS

Reasonable Effort has been made to have all illustrations and drawings accurately represent the product(s) as it actually was at the time 

of doing the illustrations and drawings.

However, products may change to meet user requirements and therefore may not be reflected in the literature.  In addition, literature 

may be up-dated to reflect the most recent equipment revision(s).  Changes to either or both equipment and/or literature can be made 

without notice.

CHANGES WITHOUT NOTICE

Prices and Specifications are subject to change without notice.

SHIPPING DATES

Shipping dates are approximate and are subject to delays beyond our control.

F.O.B. POINT AND TITLE

All material is sold F.O.B. factory. Title to all merchandise sold shall pass to Buyer upon delivery by Seller to carrier at factory. All freight 

insurance is the responsibility of the Buyer and shall be charged to the Buyer on the invoice unless directed in writing. All Freight claims 

are the Buyer's responsibility.

TERMS

Payment terms are net 30 days; 1.5% per month past due.

STATE AND LOCAL TAXES

Any taxes, duties or fees which the seller may be required to pay or collect upon or with respect to the sale, purchase, delivery, use or 

consumption of any of the material covered hereby shall be for the account of the Buyer and shall be added to the purchase price.

ACCEPTANCE

All orders shall be subject to the terms and conditions contained or referred to in the Seller's quotation, acknowledgments, and to those 

listed here and to no others whatsoever.  No waiver, alteration or modification of these terms and conditions shall be binding unless in 

writing and signed by an executive officer of the Seller. All orders subject to written acceptance by QED Environmental Systems  Inc., 

Ann Arbor, MI, U.S.A.

QED ENVIRONMENTAL SYSTEMS  INC.

2355 Bishop Circle W.

Dexter, Michigan 48130-3726

USA

(800) 624-2026 Toll-Free in North America

(734) 995-2547

(734) 995-1170 FAX

www.qedenv.com

16

Summary of Contents for Hammerhead Pro


















Reviews: