Q-Pumps QDB Series Assembly And Installation Manual Download

Page: 4 / 24

Assembly and installation manual

QIM/QDB Mixer Series

QIM/QDB-M01

IMPORTANT SAFETY INFORMATION

Safety is very important!

DO NOT attempt to modify any Q-Pumps product,

the

QIM/QDB Mixer Series

have been

designed to be safe and reliable, to do so could create unsafe conditions and void all warranties.

DO NOT place any Q-Pumps product in an application where general product service

ratings are exceeded.

If the maintenance and operation personnel do not observe the

instructions in this manual could result in personal injury or machine damage.

The following

DANGER, WARNING, and CAUTION

signs and their meanings are used within

these instructions to avoid serious injury and/or possible damage to equipment.

CODE 136530002

(Guard warning)

Safety labels are placed on every pump. DO NOT remove any labeling on any Q-Pumps pro-

duct. Replace any label that is missing.

WARNING

ROTATING SHAFT

DO NOT OPERATE

WITHOUT GUARD IN PLACE

Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury. The word danger is used in the

most extreme cases.

DANGER

Indicates a potentially hazardous situation

which, if not avoided, could result in minor

or moderate injury. May also be used to alert

against an unsafe operating or maintenance

practice.

WARNING

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

CAUTION

CODE 136530001

(Rotating direction ccw)

Summary of Contents for QDB Series

























Search results

Summary of Contents for QDB Series

Reviews:

Related manuals for QDB Series

Brands by name

Popular brands

Q-Pumps QDB Series, Assembly And Installation Manual

Search results

Summary of Contents for QDB Series

Reviews:

Related manuals for QDB Series

Brands by name

Popular brands