Q-Pumps QDB Series Assembly And Installation Manual Download | Manualshive

Page: 10 / 24

background image

10

Assembly and installation manual

QIM/QDB Mixer Series

QIM/QDB-M01

START THE ASSEMBLY

It is highly recommended that you use the general diagram to identify

the components and thus be able to carry out the assemblies and sub-

assemblies that will be explained below.

1. LEG BRACKET ASSEMBLIES

The leg bracket assemblies are optional. They allow to level the pumps adjusting the legs

vertically. The size of the brackets (209) and legs (207) depend on the NEMA or IEC motor

frame.

First make the sub-assemblies of the legs to the brackets with the hexagonal screws (209A).

Next, with the hexagonal screws (209B) fix the brackets to the motor base; You may need

to lift the motor to make this assembly. Figure A.

Figure A.

A

SS

EM

B

LY

«
...
8
9
10
11
12
...
»

Summary of Contents for QDB Series

























Reviews:

No comments

Related manuals for QDB Series

Brand: Oceanic Pages: 16

MULTI-TASKER MT109-102

Brand: Altinex Pages: 26

Brand: JTECH Pages: 12

Brand: Heritage Pages: 10

Brand: MQ Multiquip Pages: 2

Brand: CONSTRUCTA Pages: 14

NCS Console 4.0

Brand: NEC Pages: 20

Brand: NEC Pages: 473

Brand: NEC Pages: 173

IP4WW60DDSSACON

Brand: NEC Pages: 11

Brand: Spirit Pages: 19

Brand: Denon Professional Pages: 8

Brand: Altrad Lescha Pages: 28

Brand: Alto Pages: 20

Brand: Saramonic Pages: 2

Brand: Rane Pages: 4

Brand: Fristam Pumps Pages: 38

Brand: Hotpoint Ariston Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands