Español
9
English
Note: Regularly check that the tank is full of water.
Otherwise, fill it. The panel will show the symbol ‘Lo’,
which indicates a low water level. This tank allows for the
proper operation of the equipment.
• Open the cap of the handle and insert the deozonator
filter (this filter must be replaced every 9-12 months of
use).
• Place the jar in the centre of the base and fill it with the
water that must be hydrogenated. Select the treatment
time by using the push-button on the panel.
Note: Do not use the equipment without water in
the jar or in the tank. This could cause a break-
down.
7. NOTICE FOR OPERATION
The equipment hydrogenates the water in the jar. The
hydrogen concentration depends on the characteristics
of water and the time selected for treatment.
On this purpose, it uses an electrolytic cell separated by
a semi-permeable membrane, so molecular hydrogen
[H2] is produced in the cathode (-) and ozone [O3] and
oxygen [O2] are produced in the anode (+).
Molecular hydrogen is produced inside the jar, and the
oxygen and the ozone are disposed of outside the equip-
ment as reaction by-products through the handle. The-
refore, they are neutralised by the filter in the handle and
do not enter into contact with water stored inside the jar.
WARNING: the lower water tank must always be
full of purified water so the equipment can work
properly and to prevent damages on certain com-
ponents.
As a preventive system, the cap of the lower tank contains a
small softening filter to retain the lime which may contain
the water used to fill it. If the lower tank is empty, the display
will show and issue a BEEP sign. Fill the lower tank as
instructed.
When the equipment detects this situation three times in a
row, it will stop operation as a safety measure. In this case,
unplug the equipment from the power supply, empty the jar
• Self-cleaning cycle:
If the equipment is turned on and
the display is off, press and hold the panel for 3 seconds
until hearing a BEEP sound. The red LED will turn on and
the self-cleaning mode will be automatically activated du-
ring 10 minutes. The display will show ‘CL’. Once the pro-
cess has finished, the equipment will automatically turn
off. Dispose of all the water in the jar.
2. To stop the hydrogenation process, press the touch panel
until reaching ‘0’.
8. USER INTERFACE
1. To use the control display, gently press the touch panel with
your finger.
• Start-up and shutdown:
press the panel for 1 second, the
equipment will turn on and the control display will show ‘0’.
You will also hear a BEEP sound. Press the panel for 2 seconds
to turn the equipment off with another BEEP.
• How to select the treatment time: Each time you
press the panel, the display will show an hydrogenation
time and a blue LED will turn on. You can select between
5, 10, 20, 30 or 0 minutes (being the latter in stand-by
mode).
and fill the lower tank with purified water.
7.1. DESCRIPTION
*2 When the display shows , the equipment
indicates that the jar is not placed on the base at the
beginning of the treatment cycle or there is a poor
connection in its base.
Summary of Contents for 970213
