background image

User Manual

 

 

 

 

1.

 

Introduction 

1.1

 

Introduction to PT-PSW-41H 

The PT-PSW-41H is a professional 4K Scaler Switcher scaling HDMI/DP/VGA video signal to an 
HDMI output by selecting output resolution from 720p to 4K via OSD. 

It can work with HDMI, DP, and VGA table grommets to switch source and output black screen 
for display (table grommets sold separately). CEC and IR learning function is used to control 
display via front panel buttons. With one built-in IR In, one IR Out and one RS232, the IR and 
RS232 control signals can be used for display control. 

The PT-PSW-41H supports advanced EDID management and is HDCP 2.2 compliant. Video 
and audio sources can be selected via front panel button, table grommets or RS232 
commands by third party control device. Moreover, it features volume buttons to turn 
up/down the volume level. 

 

1.2

 

Feature 

 

Features 2 HDMI inputs, 1 DP input and 1 VGA input with auxiliary audio. 

 

The output resolution can be selected from 720p to 4K x 2K@30Hz 4:4:4   

to assure preferred output. 

 

Supports IR learning to set button function for controlling the connected display. 

 

Supports volume control via buttons. 

 

Allows the connected display to be controlled via CEC, IR, RS232 commands or front panel 

buttons. 

 

Supports HDMI/VGA/DP table grommets to control source switching and black screen 

showing. 

 

Automatically switch based on video sensing. 

 

Supports RS232 control. 

 

Supports IR pass through. 

 

Supports advanced built-in EDID management. 

 

Summary of Contents for PT-PSW-41H





























Reviews: