background image

User Manual

 

 

 

20 

 

9.

 

After-Sales Service 

If problems occur when running the product, please check and deal with the problems 
referring to this user manual. Any transport costs are borne by the user during the warranty 
period. 

 

1)

 

Product Limited Warranty: 

The product will be free from defects in materials and 

workmanship for 

two years

 (The purchase invoice shall prevail). 

Proof of purchase in the form of a bill of sale or receipted invoice which is evidence that 
the unit is within the Warranty period must be presented to obtain warranty service. 

 

2)

 

What the warranty does not cover (servicing available for a fee):

 

 

Warranty expiration. 

 

Factory applied serial number has been altered or removed from the product. 

 

Damage, deterioration or malfunction caused by: 

 

Normal wear and tear. 

 

Use of supplies or parts not meeting our specifications. 

 

No certificate or invoice provided as proof of warranty. 

 

The product model shown on the warranty card does not match with the model 
of the product for repair, or has been altered. 

 

Damage caused by force majeure. 

 

Servicing not authorized by distributor. 

 

Any other cause which does not relate to a product defect. 

 

Delivery, installation or labor charges for installation or setup of the product. 

 

3)

 

Technical Support: 

  For any questions or problems, contact your distributor or reseller 

and tell them the respective product name and version, the detailed failure situation as 
well as the formation of the cases. 

Summary of Contents for PT-PSW-41H





























Reviews: