Puls FIEPOS FPS300.246-036-104, Manual, Page: 39 / 43

FPS300.246-036-104
FPS300.246-049-102
All parameters are specified at 24 V, 20 A, 400 Vac, 25 °C ambient and after a 5 minutes run-in time unless otherwise noted.
Apr. 2022 / Rev. 0.2 FPS300-EN www.pulspower.com 39 / 43
Parameter Para.
Index
Sub-
index
Data
type
Bit
offset
Data
Format
Resolution Default
values
Read [R]
Write [W]
Allowed values Description
Temperature secondary inside 69 0 int16 15-0 Q9.7 2 -7 °C/bit R -5120…32640 Temperature secondary inside PSU -40 .. 150°C
Max. temperature secondary
inside
70 0 int16 15-0 Q9.7 2
-7
°C/bit R -5120…32640
Maximum temperature secondary inside PSU -40 ..
150°C
Temperature primary inside 71 0 int16 15-0 Q9.7 2 -7 °C/bit R -5120…32640 Temperature primary inside -40 .. 150°C
Max. temperature primary
inside
72 0 int16 15-0 Q9.7 2 -7 °C/bit R -5120…32640 Maximum temperature primary inside -40 .. 150°C
AC Input Voltage RMS 78 0 uint16 15-0 Q12.4 2 -4 V/bit R 0…24000 (0-1500V) Actual Input Voltage RMS (phase-phase)
Actual output voltage 79 0 uint16 15-0 Q8.8 2
-8
V/bit R 0…12544 (0-49V) Actual average output voltage
Actual output current 81 0 uint16 15-0 Q8.8 2 -8 V/bit R 0…12800 (0-50V) Actual average output current
E-Fuse current all CHs
84
0 Unit16 array 47-0 Q8.8 2 -8 A/bit
R
0…12800 (0-50A) Actual average E-Fuse current all CH
E-Fuse current CH1 1 uint16 47-32 Q8.8 2 -8 A/bit 0…12800 (0-50A) Actual average E-Fuse current CH1
E-Fuse current CH2 2 uint16 31-16 Q8.8 2
-8
A/bit 0…12800 (0-50A) Actual average E-Fuse current CH2
E-Fuse current CH3 3 uint16 16-0 Q8.8 2 -8 A/bit 0…12800 (0-50A) Actual average E-Fuse current CH3
E-Fuse output status
85
0
Array of bool
8-bit Record
R
0…off
1…on
Dynamic
Bit 3…7 not used
Access via subindex 0 only
Channel 1 0
Channel 2 1
Channel 3 2
E-Fuse trip status CH1
E-Fuse trip status CH2
E-Fuse trip status CH3
86 0
4-bit enum
array
3-0
7-4
11-8
R
0 = No trip
1 = Over-load trip
2 = Short circuit trip
3 = Temperature trip
4 = Power budget trip
5 = Installation failure trip
6 = Sensor fault trip
7 = Fatal fault trip
Dynamic
Bit 12…15 not used
Access via subindex 0 only
Stress level 66 0 uint8 7-0 R
0 … “<=5%”
1 … “>5%”
2 … “>=25%”
3 … “>=50%”
4 … “>=75%”
current load