PSI PP 2024 User Manual Download Page 44

Page: 44 / 116

Explanation of Individual Menu Items

4-13

4-14

4.3

Menu Mode BASIC SETTINGS

MENU ACCESS

4.3.1

CONFIG MENU

MENU ACCESS

, defining the access rights to various submenus. The

In the Configuration Menu general settings for the printer´s operation are

locked submenus aren’t displayed on the panel. However, configuration

defined.

changes by means of PJL commands are possible.

POWER SAVE

The access rights can be changed with the following combination of operator

The time until the power save mode is entered can be set to

panel keys:

MIN

OFF

; factory default is

15 MIN

OFF

The printer doesn´t switch into the POWER SAVE mode.

Choose the new access right in

MENU ACCESS

In power save mode the printer switches off the fuser lamps, the fans, and

the selection

motors. Power dissipation in POWER SAVE mode is

less than 45 watt

. The

Press

ESCAPE

within the next two seconds.

messsage

POWER SAVE

is displayed. A new print job causes the POWER

Save with the key

once more.

SAVE mode to be left.

If there are no new messages to be displayed within the next

15 minutes

the

complete sequence has to be started again.

panel light is switched off as well. This function is independent of the choosen

POWER SAVE time.

RECALL FACTORY

ALARM BELL

profiles are reset to the factory defaults. This function needs to be confirmed

Any error that occurs during a print operation is reported by a corresponding

by the additional prompting YES/NO to prevent unintended reset of all

error message on the display, additionally the buzzer in the operator panel

parameters.

electronics is activated. The signals can be stopped by either pressing any

key on the panel or by opening the cover. The default setting is

. To

Note:

The printer needs up to

two minutes

for reset !

disable this function set the value to

OFF

LANGUAGE

Selects the language of the menu.

Default is

ENGLISH;

available are:

ENGLISH, FRANCAIS, DEUTSCH (German), ITALIANO, and ESPANOL

Note:

Only in English and German all display messages are fully supported in

the individual language.

The menu

CONFIG MENU

has been extended by the new function

access rights could defined being

ALL

ONLY PROFILE

, or

NOTHING

. The

Choose the option and save it with the key

. An asterisk indicates

Note:

A wrong key sequence results in cancelling the current trial and the

By calling up

RECALL FACTORY

CONFIG. MENU

all menus, including all

Summary of Contents for PP 2024





















































































































Search results

Summary of Contents for PP 2024

Reviews:

PSI PP 2024, User Manual, Page: 44 / 116

Search results

Summary of Contents for PP 2024

Reviews: