manualshive.com logo in svg

PSI PP 2024, User Manual, Page: 27 / 116

Share
Download
PSI PP 2024 User Manual Download Page 27

ON LINE

MENU

ON LINE

Configuring the Printer Configuring the Printer

3-3 3-4

3.2 Printout of Standard Configuration 3.2.1 How to Start a SELF TEST

The factory default configuration can be printed within the 

TEST MENU

 and is

shown on the following page.

The upper part of the 

SELFTEST

 printout shows the actual selections and

parameter values.

Main functions appear in the first line of each menu block.

Second and following lines show the selection at subfunction level and the

selected parameters behind the "=" sign.

Below the menu section on the test page information is given about the

hardware and software configuration of the printer and stacker:

S 

FLASH memory size for printer firmware and fonts

S 

memory size (DRAM)

S 

Printer and Stacker firmware version

S 

Panel version

S 

available emulations

The rest of the page is filled up with a diagonal test pattern. The black frame

around the test page reflects the actual paper format. The default format is 12

inch for paper length and 8.25 inch for image width.

Panel keys are now used and associated display messages are shown for the

next steps. The following example demonstrates how to do so:

Key Display

 1. Switch the printer on. ONLINE      (1)

 2. Press    (97) OFFLINE    (1)

Note:

The number in brackets behind 

ONLINE

 or 

OFFLINE

 indicates the selected Profile.

 3. Press    (92) OFFLINE    (1)

SELECT PROFILE 

6

6

 4. Press    (95) OFFLINE    (1)

RESET PRINTER 

6

6

 5. Press    (95) OFFLINE    (1)

TEST MODE 

6

6

 6. Press    (93) TEST MODE

TEST MENU 

6

6

 7. Press    (93) TEST MENU

PANEL TEST 

6

6

 8. Press    (94) 

TEST MENU

SELF TEST

 9. Press    (93) 

TEST MENU

SELF TEST 

*

The printer starts with the SELFTEST printout. When printing is completed, the

following message will be displayed

10.  TEST MENU

SELF TEST

11. Press    (97) ONLINE    (1)

The printer returns to the operating mode after pressing the 

ONLINE

 key:

Summary of Contents for PP 2024





















































































































Reviews:

No comments