PROSPOTfitness Fusion SSG, Owner'S Manual, Page: 5 / 22

STEP #3 – WEIGHT STACK INSTALLATION & SENSOR WEIGHT (con’t)
11. Now install (#34) Accessory holders using (#99) bolts, (#90) flat washers & (#91) lock nuts.
12. Now tighten all bolts just installed. First tighten the bolts and nuts holding the (#15, #51) right
& left Folding Uprights hinge points. Then start tightening bolts starting at the floor and work
your way up the unit until all bolts are tight. Do not over tighten. Check folding function of
unit. Adjust by loosing bolts and move frame member and retighten.
13. Next install (#7) Logo plate with (#97) screws.
14. Now install (#23 & #43) Locking Post Covers onto (#31right, #35 left) Locking Posts using
(#115) screw and (#101) washer. Tighten screws.
15. Now connect (#145) 12V Power supply to Electronic Box. A flashing green light should
appear to verify power and ready.
16. Now its time to install (#46) Sensor Weight Bar. Using a 5mm allen wrench remove the
(#139) Socket Button Head Screw & (#59) End Cap off each end. Now using a 4mm allen
wrench, remove the (#38) Spacer collar from each end of Sensor Weight Bar. This may
take two people to perform this next task. Place Sensor Weight Bar in front of unit. Grab and
touch the metal plate on the (#58) Weight Bar Cable Knuckles that are on the front of the
unit. This will trigger the sensor to release the Cables to allow down ward movement. Pull
down to waist level and hold these at this position. Make sure Cables are not twisted and the
metal face of Cable Knuckle is facing inward. If you let go the Cables, they will retract back
into unit. Now have your assistant slide end of the (#46) Sensor Weight Bar thru holes in
knuckles on each side. Note: There is a key slot cut out in Cable Knuckle for a metal pin on
Sensor Weight Bar to slide thru. You can now let go of Sensor weight Bar. It will not move
unless Sensor is triggered. Now reinstall (#38) Spacer collar so that it is against Cable
Knuckle and tighten with 4mm allen wrench. Now install the (#37) Olympic adapters, (#59)
End Cap and tighten (#139) Socket Button Head Screw with 5mm allen wrench.
STEP #4 – BENCH ASSEMBLY
1. Now according diagram #4, install (#79) spring shocks to previously installed (#71) Bottom
frame assembly using (#125) bolt, (#130) Spacer, (#101) washer, (#102) nut and tighten.
11. Now position (#152) Bench Slider Rail between (#82 & #83) Bench Swivel Plates and secure
with (#107) bolts, (#90) flat washers and (#91) lock nuts. Tighten Securely.
2. Now lift Bench Assembly up to vertical position and hold. Do not let go. This may take two
people to perform this task. Now connect (#78) Spring Shock Mounting Bracket to bottom of
(#152) Bench Slider Rail using (#115) Screws and (#101) washers. Tighten securely.
3. Now lower Bench Assembly to floor. Now install (#69) Bench Seat Frame using (#124) bolt,
(#90) flat washer and (#91) lock nut and tighten securely.
4. Now install (#122) Seat Adjustment Frame into (#69) Bench Seat Frame slot and secure
with bolt (#124) bolt, (#90) flat washer and (#91) lock nut and tighten securely.
5. Next according to diagram #4, install (#66) Bench Seat Pad onto 69) Bench Seat Frame with
(#138) bolt and (#87) washer and tighten securely.
6. Now according to diagram #4, install (#129) Plastic Spacing Sleeve & (#62) Foam Roller
onto (#69) Bench Seat Frame tubes.
Page 5