ProSoft Technology inRAx MVI46-PDPMV1 User Manual Download Page 17

Page: 17 / 160

MVI46-PDPMV1 ♦ SLC Platform

Start Here

PROFIBUS DPV1 Master

User Manual

ProSoft Technology, Inc.

Page 17 of 160

March 25, 2011

Check that the holding clips on the top and bottom of the module are securely

in the locking holes of the rack.

Make a note of the slot location. You will need to identify the slot in which the

module is installed in order for the sample program to work correctly. Slot

numbers are identified on the green circuit board (backplane) of the SLC

rack.

Turn power ON.

Note:

If you insert the module improperly, the system may stop working, or may behave

unpredictably.

Summary of Contents for inRAx MVI46-PDPMV1

































































































































































Search results

Summary of Contents for inRAx MVI46-PDPMV1

Reviews:

Related manuals for inRAx MVI46-PDPMV1

Brands by name

Popular brands

ProSoft Technology inRAx MVI46-PDPMV1, User Manual

Search results

Summary of Contents for inRAx MVI46-PDPMV1

Reviews:

Related manuals for inRAx MVI46-PDPMV1

Brands by name

Popular brands