Promise Technology ConnectStor II User Manual Download Page 19

Page: 19 / 86

Chapter 2: Getting Started

5. Type the IP address you want to use in the

IP Address:

field (above).

6. Type 255.255.255.0 in the

Subnet Mask:

field.

7. Type the IP address of your Gateway server in the

Gateway:

field.

8. Click

the

Assign IP

button.

CAUTION

: Check and recheck your entries in this menu.

Incorrect entries will prevent you from seeing the ConnectStor
II on your system.

After you click the Assign IP button, IPassign will verify that your settings are
correct and the requested IP address is not already in use. If everything is correct, the
IPassign dialog box will display the new IP address information (below).

NOTE:

If there is no IP address assigned within ten minutes,

either through the APassign utility or the DHCP server, the
ConnectStor II will set its own IP address to 192.168.204.204.

Summary of Contents for ConnectStor II























































































Search results

Summary of Contents for ConnectStor II

Reviews:

Related manuals for ConnectStor II

Brands by name

Popular brands

Promise Technology ConnectStor II, User Manual

Search results

Summary of Contents for ConnectStor II

Reviews:

Related manuals for ConnectStor II

Brands by name

Popular brands