Prominence Home Liva 51016 Owner'S Manual Download Page 9

9

OPERATING INSTRUCTIONS

1

2

Light Pull 

Chain 

Reverse Switch

Fan Pull Chain

2. Use the reverse switch, located on the light kit to 

optimize your fan for seasonal performance.
Using a ceiling fan will allow you to raise your thermostat 

setting in summer and lower your thermostat setting in 

winter without feeling a difference in your comfort.

In warmer weather

, push the reverse switch to the left 

which will result in downward airflow creating a wind 

chill effect. 

In cooler weather

, push the reverse switch to the right 

which will result in upward airflow that can help move 

stagnant, hot air off the ceiling area. 

Important: 

Wait for the fan to stop before moving the 

reverse switch. The reverse switch must be set either 

completely left or right in order for the fan to function 

correctly. If the reverse switch is set in the middle 

position, the fan will not operate.

1.The fan pull chain has four positions to control the fan 

speed. One pull is HIGH, two is MEDIUM, three is LOW, 

and four turns the fan OFF. The pull chain in the center of 

the light kit turns the lights ON and OFF.

Summary of Contents for Liva 51016












Reviews: