background image

www.usaprocom.com

7

200198-01A

AIR FOR COMBUSTION AND VENTILATION

 WARNING: This heater shall 

not  be  installed  in  a  confined 

space or unusually tight con-

struction unless provisions are 

provided for adequate combus-

tion and ventilation air. Read the 

following instructions to insure 

proper fresh air for this and other 

fuel-burning appliances in your 

home.

Today’s homes are built more energy efficient 

than ever. New materials, increased insulation 

and new construction methods help reduce 

heat loss in homes. Home owners weather 

strip  and  caulk  around  windows  and  doors 

to keep the cold air out and the warm air in. 

During heating months, home owners want 

their homes as airtight as possible.

While it is good to make your home energy 

efficient, your home needs to breathe. Fresh 

air must enter your home. All fuel-burning ap-

pliances need fresh air for proper combustion 

and ventilation.

Exhaust fans, fireplaces, clothes dryers and 

fuel  burning  appliances  draw  air  from  the 

house to operate. You must provide adequate 

fresh air for these appliances. This will insure 

proper venting of vented fuel-burning appli-

ances.

 WARNING: This heater shall 

not  be  installed  in  a  room  or 

space unless the required vol-

ume  of  indoor  combustion  air 

is provided by the method de-

scribed in the National Fuel Gas 

Code, ANSI Z223.1/NFPA 54, the 

International Fuel Gas Code, or 

applicable local codes.

 WARNING: If the area in which 

the heater may be operated does 

not meet the required volume for 

indoor combustion air, combus-

tion and ventilation air shall be 

provided by one of the methods 

described  in  the  National Fuel 

Gas Code, ANSI Z223.1/NFPA 54, 

the International Fuel Gas Code, 

or applicable local codes.

VENTILATION AIR

Ventilation Air From Inside Building

This fresh air would come from an adjoining 

unconfined  space.  When  ventilating  to  an 

adjoining unconfined space, you must provide 

two permanent openings: one within 12" of the 

ceiling and one within 12" of the floor on the 

wall connecting the two spaces (see options 

1 and 2, Figure 2). You can also remove door 

into adjoining room (see option 3, Figure 4). 

Follow  the 

National Fuel Gas Code, ANSI 

Z223.1/NFPA 54, Air for Combustion and 

Ventilation

  for  required  size  of  ventilation 

grills or ducts.

Figure 4 - Ventilation Air from Inside 

Building

Or

Remove

Door into

Adjoining

Room,

Option

3

Ventilation Grills 

Into Adjoining Room,

Option 2

Ventilation

Grills Into

Adjoining 

Room,

Option 1

12"

12"

Summary of Contents for QNSD250T





























Reviews: