background image

© 2017 by Proceq SA   

       

12

© 2017 by Proceq SA   

       

13

5.4. Basic Measurement – Waveform Display

Select “Basic
Measurements”

Start the measurement

Select “Waveform”

Adjust as required
(See below)

Cancel to return to
standard display

Waveform Controls

Y < > 

Vertical zoom

X < > 

Horizontal zoom

t   - + 

Manual trigger adjustment

 Stop/Start

Note 1: Rx gain may need reducing for vertical zoom to have a noticeable effect.
Note 2: Once adjusted, trigger point does not reset automatically unless a new measurement is started 
in the menu “Start the measurement”
Note 3: The waveform is not saved, only the transmission time.

5.5. Basic Measurement – Path Length

If the pulse velocity of the material under test is known, it is possible to measure the path length 
between the transducers. The procedure is exactly the same as for measuring pulse velocity ex-
cept that in this case the known pulse velocity is entered.

Select
“Basic Measurements”

Select parameter setting 
“pulse velocity”

Enter the pulse velocity

Start the measurement

The display shows:
- Transmission time
- Measured path length
- Received signal level

Stop the measurement
(Not necessary in burst mode)

Save the result or:
Adjust the gain settings.
(See Chapter 3) or:
Start a new measurement

Summary of Contents for Pundit Lab


















Reviews: