background image

© 2017 by Proceq SA   

       

4

© 2017 by Proceq SA   

       

5

2. Getting started

Rear Panel

Connectors for: 
Oscilloscope

USB – PC / Power Supply

The Pundit Lab can be powered by batteries, by the mains or by the USB connection to a PC.

Front Panel

The soft keys are context sensitive. The display 
icon shows the active function.

The lower right-hand key is for Power ON/OFF 
and also to “Cancel” a setting and return to the 
previous menu.

The navigation key is for scrolling through menus and for setting variable parameters.

Transducer Connection

Connect the transducers to the front of the display unit using the BNC cables. If cables of dif-
ferent lengths are used, the longer cable should be connected to the transmitter.

i

Note: 

To avoid the possibility of electrical shock, the transducers must be con-

nected before switching on and disconnected only after switching off.

Basic Measurement

Compound Measurement

System Settings

Information

Power ON

Press and hold the lower right-hand key for 3 seconds. The main menu and the type "Pundit 
Lab" or "Pundit Lab

+

" is displayed.

Clicking on the “Information” soft key brings up important device information.

  

Battery status or

USB connection

 

 

Serial number

Hardware version
Firmware version

Power Management – Power OFF

When operating on battery power the instrument goes into standby mode after 5 minutes of 
inactivity. After 30 minutes it shuts down completely. When powered by the USB connection, 
the display shuts down after 1 hour of inactivity. Press the lower right hand key (Power ON/
OFF, Cancel) to recover from standby mode. To power off, press and hold the lower right-hand 
key for 3 seconds.

Zeroing the Pundit Lab

The Pundit Lab should be zeroed 
using the calibration rod on a 
regular basis and in particular if the 
transducer frequency is changed or if 
the cables are changed. The expected 
calibration value (µs) is marked on the 
calibration rod. 

Couple the transducers to the 
calibration rod by applying couplant 
to the transducers and both ends of 
the rod and pressing firmly together 
as shown.

i

Note: 

When zeroing the exponential transducers the dedicated calibration rod  

(325 40 174) should be used.

 
Select System Settings
(See chapter 3 for more info)

Check Tx/Rx matches transducer 
frequency. Pulse width requires no 
adjustment.
Correction factor set to 1.0. 
Select Calibration.

If necessary, select to enter the transit 
time as marked on the calibration rod.

Variable parameter; set as follows:

Up/down keys  - fine adjustment
Left/right keys  - coarse adjustment.
Center key  - enters the value and 
returns to the previous menu.
Cancel key  - cancels the input and 
returns to the previous menu.

Press “Start” to begin the calibration 
sequence.

The final display shows the expected 
transit time and below it the measured 
transit time. This should match the 
value on the calibration rod.

Batteries

Summary of Contents for Pundit Lab


















Reviews: