Probe PMA-H2000 User Manual Download Page 3

Important Safety Instructions

1.    

Read these instructions.

 - All these safety and operating instructions should be read before the product is operated.

2.    

Keep these instructions.

 - The safety, operating and use instructions should be retained for future reference.

3.    

Heed all warnings.

 - All warnings on the product and in the operating instructions should be adhered to.

4.    

Follow all instructions.

 - All operating and use instructions should be followed.

5.    

Do not use this apparatus near water.

 - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a

        wet basement; near a swimming pool; etc.

6.    

Clean only with dry cloth.

 - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7.    

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

 - Slots and

        openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
        from over-heating.  The openings should never be blocked by placing the product on bed, sofa, rug or other similar
        surface.  This product should not be placed in a built-in installation such as a bookcase or rack unless proper
        ventilation is provided and the manufacturer’s unstructions have been adhere to.

8.    

Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers)

        that produce heat.

 

9.    

Do not defeat the safety purpose of the polarized or grounding-type plug.  A polarized plug has two blades with

        one wider than the other.  A grounding type plug has two blades and a third grounding prong.  The wide blade
        or the third prong are provided for your safety.  If the provided plug does not fit into your outlet, consult an 
        electrician for replacement of the obsolete outlet.

10.  

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

         the point where they exit from the apparatus.

11.  

Only use attachments/accessories specified by the manufacturer.

12.  

Use only with cart, stand, tripod, bracket, or table specified by the 

        manufacturer, or sold with the apparatus. When a cart is used, use
        caution when moving the cart/apparatus combination to avoid
        injury from tip-over.

13.  

Unplug this apparatus during lightning storms or when unused for long periods of time.

14.  

Refer all servicing to qualified service personnel.  Servicing is required when the apparatus has been damaged

         in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
        apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
        dropped.

Summary of Contents for PMA-H2000





























Reviews: