background image

Operating instructions LITTY 4you 

 

24

 

27 Disposal 

At the end of the service life, the product can 
be disposed of by PRO ACTIV or your dealer 
in a proper, environmentally-friendly manner. 

 

28 Re-use 

If your product has been provided to you by 
your funding provider and you no longer re-
quire it, you should report this fact to your 
health insurance company or your dealer. Your 
product can then be simply and economically 
re-used. 

Before any re-use, a safety check must be 
carried out on the product by PRO ACTIV. The 
system must be checked for corrosion. In addi-
tion to the instructions contained in chapter 25 
(Cleaning and care), a thorough cleaning of all 
controls must be carried out before using it 
again. This will also be done by PRO ACTIV as 
part of the safety check. This safety-related 
check must be initiated by the funding provider. 

 

29 Warranty 

PRO ACTIV guarantees that the product was 
free of any defects at the time it was handed 
over. This warranty expires 24 months after the 
product was delivered.  

Further information can be found in PRO AC-
TIV's general terms and conditions at 

www.proactiv-gmbh.com

 Any modifications to the product which 

have not been expressly approved by PRO 
ACTIV will invalidate the warranty. Such modi-
fications may cause unforeseeable safety risks 
and are therefore not permitted. 

 

 

 

 

 

30 Liability 

As the manufacturer of the product, PRO AC-
TIV is not responsible for its safety if: 

 

the product is handled improperly 

 

the product is not maintained in accor-
dance with the maintenance schedule laid 
down by PRO ACTIV 

 

the product is commissioned and used 
contrary to the instructions in these operat-
ing instructions 

 

repairs or other work are carried out by 
non-authorised persons 

 

third-party parts are installed or connected 
to the product 

 

Further information can be found in PRO AC-
TIV's general terms and conditions at  

www.proactiv-gmbh.com

 

 

Summary of Contents for LITTY 4you









































Reviews: