Pro-face GP-2300 Series User Manual Download Page 61 | Manualshive

Page: 61 / 61

Pro-face GP-2300 Series User Manual Download Page 61

Chapter 6 - Maintenance

GP-2300/2301 Series User Manual

6-4

Use the following table to check that you have ordered the correct backlight.

6.3

Replacing the Backlight

When the unit’s backlight burns out, the unit’s status LED will turn orange. If the
OFFLINE menu’s “USE TOUCHPANEL AFTER BACKLIGHT BURNS OUT”
feature is set to “NO”, the GP’s touch panel will be disabled.

*1

The GP-2300L and GP-2301 Series units use a CFL, long-life type backlight. The
actual life of the backlight however, will vary depending on the GP’s operating
conditions, and replacement may be required. A GP2000 Series backlight has a
life of 50,000 hours (approx. 5.7 years, at 25

o

C and 24 hour operation), when the

backlight is lit continuously (time required for brightness to fall to half its normal
level.)

For backlight replacement details, refer to the replacement backlight
unit’s installation guide.

*1

If “NO” has been selected for the OFFLINE menu’s “FORCE RESET” feature,
Touch-Panel operation is disabled.

WARNINGS

• To prevent an electric shock, be sure the GP’s power cord

is unplugged from the power outlet prior to replacing the
backlight.

• When the power has just been turned OFF, the unit and

backlight are still very hot. Be sure to use gloves to pre-
vent burns.

• The backlight is very fragile. Do not touch the glass tube

directly or try to remove its power cord. If the glass tube
breaks you may be injured.

GP Model

Backlight Model

GP2300-LG41-24V

GP2301-SC41-24V

GP2301-LG41-24V

PS300-BU00

The GP2300T/GP2301T’s backlights cannot be replaced by the customer.

When the backlights need to be replaced, please contact your local GP
distributor.

«
...
59
60
61

Summary of Contents for GP-2300 Series






























































Reviews:

No comments