manualshive.com logo in svg

Pro-face GP-2300 Series, User Manual, Page: 13 / 61

Share
Download
Pro-face GP-2300 Series User Manual Download Page 13

Preface

GP-2300/2301 Series User Manual

12

Symbol

Meaning

Indicates important information or procedures that must be followed for
correct and risk-free software/device operation.

Screen

Editor

Indicates the Pro-Designer (version 4.0 or higher).

PLC

Abbreviation for Programmable Logic Controller.

*1

Indicates useful or important supplemental information.

1) , 2)

Indicates steps in a procedure. Be sure to perform these steps in the
order given.

Provides useful or important supplemental information.

Refers to useful or important supplemental information.

The list below describes the documentation conventions used in this manual.

Documentation Conventions

CE Marking Notes

The GP2300-LG41-24V, GP2300-TC41-24V, GP2301-LG41-24V, GP2301-SC41-
24V and GP2301-TC41-24V are CE marked products that conform to EMC
directives EN55011 Class A and EN61000-6-2.
For detailed CE marking information, please contact your local GP distributor.

Revision Information

Revision information can be found on your GP unit’s rear-face Pro-face label. The
bottom-most [REV] row’s asterisk (*) mark indicates the Revision character.

In the example shown below, the asterisk indicates that this unit’s Revision char-
acter is “D”.

DIGITAL ELECTRONICS CORP.

Summary of Contents for GP-2300 Series






























































Reviews:

No comments