background image

13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com

IMPORTANT!: 

• Please refer to the Prima catalog for proper lamp type & max. wattage.

   

• Prima is not responsible for any fixture or system failure caused by lamps not supplied by Prima.
• Always contact Prima customer service for the latest updates on the proper use of the lamps.

• A specified transformer from Prima is needed for the low voltage FIT II System installations.
• Prima Lighting will not warrant the fixtures or systems if Prima transformers are not used.
• The Prima Lighting catalog provides general suggestions as to the proper style of dimmer switch.

However, always consult Prima customer service for the use of any specific dimmer. 

• Prima Lighting is not responsible for any fixtures damaged or system malfunctions caused 

• This track system is not intended for use with a power supply cord or convenience receptacle adapter.

by the incompatibility of non-specified or suggested dimmers.

REV. 052416

PRIMA LIGHTING - FIT II SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

IF YOU HAVE ANY QUESTIONS REGARDING THE INSTALLATION OF 

THIS PRODUCT, PLEASE CALL PRIMA CUSTOMER SERVICE AT

1-562-407-3079 

INSTALLATION INSTRUCTION

A) READ ALL OF THESE INSTALLATION INSTRUCTIONS BEFORE INSTALLING THE FIT II

     SYSTEM.

B) DO NOT INSTALL THIS SYSTEM IN DAMP OR WET LOCATIONS.

C) DO NOT INSTALL THIS SYSTEM OR ANY PART WHICH CONTAINS EXPOSED

WIRES LESS THAN 7 FEET FROM THE FLOOR.

D) DO NOT INSTALL ANY LUMINAIRE ASSEMBLY CLOSER THAN 6 INCHES FROM 

ANY CURTAINS OR SIMILAR COMBUSTIBLE MATERIAL.

E) DISCONNECT ELECTRICAL POWER BEFORE ADDING TO OR CHANGING THE

CONFIGURATION OF THE TRACK.

F) DO NOT ATTEMPT TO ENERGIZE ANYTHING OTHER THAN LIGHTING TRACK

LUMINAIRES ON THE TRACK. TO REDUCE THE RISK OF FIRE AND ELECTRIC

SHOCK, DO NOT ATTEMPT TO CONNECT POWER TOOLS, EXTENSION CORDS,

APPLIANCES, AND THE LIKE TO THE TRACK.

G) DO NOT CONNECT A TRACK TO MORE THAN ONE BRANCH CIRCUIT UNLESS

THE TRACK IS CONSTRUCTED SO THAT IT CAN BE USED WITH MORE THAN

ONE BRANCH CIRCUIT. CHECK WITH A QUALIFIED ELECTRICIAN. 

SAVE THESE INSTRUCTIONS AND REFER TO THEM WHEN ADDITIONS

TO OR CHANGES IN THE TRACK CONFIGURATION ARE MADE. THESE

INSTRUCTIONS CONTAIN IMPORTANT INFORMATION REGARDING

YOUR NEW PRIMA LIGHTING FIXTURES.

Summary of Contents for FIT II











Reviews: