M3
Rotate the top knurled knob counter
clockwise to tighten and secure the
contact. There should now be a gap
between the two knurled knobs.
M2
Insert the power feed into the track and
rotate the bottom knurled knob
counter clockwise until the feed rest
perpendicular to the track.
M1
Neutral Installation Instructions
Ensure that there is NO gap in between
both knurled knobs prior to installation.
L3
Rotate the bottom knurled knob
counter clockwise to tighten and
secure the contact. The gap between
the two knurled knobs should now be
smaller.
L2
Insert the power feed into the track and
rotate the top knurled knob counter
clockwise until the feed rest
perpendicular to the track.
Ensure that the top knurled knob is
raised as much as possible prior to
installation.
L1
Designed only for the
bottom track in the
vertical orientation.
pr
ima fit II sy
st
em
general installation instructions part 6 of 6
Follo
w all local and na
tional elec
tr
ical c
odes
.
For assistanc
e please call P
rima C
ust
omer S
er
vic
e a
t 562-407-3079
NEUTRAL
HOT
Designed only for the
bottom track in the
vertical orientation.
HOT Installation Instructions
Wire must be fed
Wire must be fed
CAUTION
Always disconnect power prior to installation
or maintenance.
NOTE:
1. Both the Neutral and the Hot must be inserted into the same track in order to receive voltage.
2. Test Voltage and Temperature after installation to ensure proper installation and conductivity.
3. Remove the power feed before moving to ensure finish of track.
Voltage & Temperature Readings
Voltage: 11.3V 1 11.7V w/ 85% to 90% load
Temperature: 80° - 90°F Room Temperature
This additional piece is
necessary for Fit II
application.
13615 Marquardt Ave. Santa Fe Springs, CA 90670
Ph. 562-407-3079 . Fx. 562-407-3069
www.primalighting.com
fit II system support for vertically oriented track
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures.
Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper
dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.
It is strongly recommended that gloves are used when handling the FIT II System track. Oils and dirt from fingers can sometimes permanently
mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.
fit II system two piece power feed
IMPORTANT Please read these instructions prior to installation. Refer to the Prima catalog for proper lamp type and maximum wattage for fixtures.
Prima is not responsible for any fixture or system failure caused by unsupported lamps. Contact Prima customer service for the latest updates on
which lamps we support and proper usage. Prima low voltage transformers must be used with all Prima Lighting product installations. All warranties
are void if Prima transformers are not used. Prima’s catalogs provide general information and suggestions for proper dimmer usage. Please consult
our customer service department with any questions regarding dimmer specifics. Prima is not responsible for any damage caused by improper
dimmer specification and usage. Use only qualified electrician for installation. Adhere to all local and national electrical codes prior to installation.
It is strongly recommended that gloves are used when handling the FIT II System track. Oils and dirt from fingers can sometimes permanently
mark the finish. Track should be cleaned with a damp cloth and thoroughly dried before fixture installation.
(22-79300-2)
REV. 052416
