background image

10

Go-Go Travel Lift

www.pridemobility.com

ADJUSTMENT PIN

TOP TUBE

LIFTING
HOOK

ADJUSTMENT HOLES

BOTTOM  TUBE

!

!

Figure 7. Split Ring Collar

Figure 8. Boom Arm Adjustment

SCREWS

BOW TIE COTTER PIN

SECURE NO CLOSER THAN 5”
(12.5 CM)  FROM THE TOP OF
THE POST.

I I I .   I N S T A L L A T I O N

SPLIT RING COLLAR ADJUSTMENT

The split ring collar is the height adjustment for the motor
housing. See figure 7. The placement of the split ring
collar determines the height of the motor housing.

"

Lower the collar when more room is needed over-
head to swing the boom arm inside a vehicle.

"

Raise the collar when more height is needed to en-
able a scooter to be lifted into a trunk.

To adjust the split ring collar:
1. Loosen the two screws on the collar. See figure 7.
2. Raise or lower the collar to the height you may need.
3. Tighten the screws

BOOM ARM ADJUSTMENT

Before adjusting the boom arm, lower the lifting hook
about 12 in. (30 cm). This will provide enough slack in
the strap to enable the adjustable portion of the boom
arm (top tube) to be pulled out of the bottom tube to its
farthest adjustment hole. See figure 8.

To adjust the boom arm:
1. Remove the bow tie cotter pin from the adjustment

pin and remove the adjustment pin.

2. Slide the top tube in or out to the desired adjustment

hole.

3. Align the adjustment holes of the top and bottom tube

and reinsert the adjustment pin.

NOTE: Do not force the pin into the adjustment
hole. Be sure that the strap is not pinched when
inserting the pin.

4. Reinstall the bow tie cotter pin.

L-BASE INSTALLATION

After determining the ideal spot for your lift to be permanently mounted, remove the entire lift from the vehicle
except for the L-base.
1. Inspect the undercarriage of the vehicle where the lift L-base is located for obstructions that may hinder the

installation of the five (5) mounting bolts that will secure the L-base to the vehicle. Obstructions may consist of
electrical wiring, gas tank, bumper mounts, or exhaust pipes. You may need to adjust the base extensions to
clear obstructions. If possible, install the L-base with the base extensions fully extended. See figure 9.

WARNING! The bumper mounts on some vehicles are gas pressured. DO NOT drill into

them. They may explode casing severe injury.

Summary of Contents for Go-Go Travel Lift




















Reviews: