12
Default Priority channel 2 is
19
AM
.
See §
PRIORITY CHANNELS
page 9.
8) VOX SET
Three parameters allow to
adjust
the
VOX
function: Sensitivity:
L
/ Anti-vox
level:
A
/ Vox delay time:
t
.
Push the rotary
PUSH
knob (
6
) for 3 seconds to
enter
MENU
. is displayed.
1.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the
VOX SET
menu.
2.
Push the rotary
PUSH
knob (
6
) to
validate.
The current
parameter
blinks on
LCD:
A
,
L
or
t
.
3.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
To
select
another parameter other than the one displayed or...
4.
Push the rotary
PUSH
knob (
6
) to
validate.
The current
value
of the selected
parameter blinks on LCD.
5.
Turn the rotary
PUSH
knob (
6
) or press the
UP
/
DN
(
18
) keys on the microphone
to
modify
the value.
6.
Push again the the rotary
PUSH
knob (
6
) to
store
and
move
to next setting...
7.
Once the settings done, press the
PTT
switch (
17
) key to
exit
the
VOX Adjust-
ment
mode. If no adjustment is made for 10 seconds, the unit automatically
exits the menu.
-
Sensitivity
“
L
”
: allows the adjustment of the microphone (original one or
optional vox) for an optimum transmission quality. Adjustable level from
1
(high level) to
9
(low level).Default value:
2
.
-
Anti-Vox
“
A
”
: allows disabling the transmission generated by the surrounding
noise. The level is adjustable.
OF
(according the squelch level) and from
0
(without anti-vox) to
9
(low level). Default value:
Of
.
-
Delay
time
“
T
”
: allows avoiding the sudden cut of the transmission by
adding a delay at the end of speaking. The level is adjustable from 1
(short delay) to 9 (long delay). Default value;
1
.
The
Vox Adjustment
does not automatically active the
VOX
function.
9) SWR ADJUSTMENT
This function allows to
adjust
the SWR (Standing Wave Ratio) by beep tones.
Push the rotary
PUSH
knob (
6
) for 3 seconds to
enter
MENU
. is displayed.
1.
Turn the rotary
PUSH
knob (
6
) or use the
UP
/
DN
buttons (
18
) on the micro-
phone to
select
the
SWR
menu.
2.
Press the rotary
PUSH
knob (
6
). The radio automatically goes to
TX
mode
without pressing
PTT
switch (
17
) . The
SWR
measurement starts. Measurement
time is 5 minutes maximum. The remaining time is displayed.
3.
Adjust your antenna.
4.
The beep tone
*
is continuous when SWR value is equal to
1.0
. The space
between two beeps became longer when SWR value moves away from
1.0
.
Display shows the
SWR
value. For example
2.5
.
5.
Press
PTT
switch (
17
) to
exit
MENU
mode. disappears in the display.
*Volume of the beep tone is adjustable with
VOLUME
knob (
1
). Please check
that the beep volume is set to a comfortable listening level.
See §
HOW TO ADJUST SWR
page 6.
10) MIC TYPE
The PRESIDENT WALKER III FCC can be used with an electret microphone as
well as with the dynamic one, 6-pin PRESIDENT
(see the cabling diagram
page 60)
. Turning on the unit, the type of the microphone is briefly dis-
played.
Push the rotary
PUSH
knob (
6
) for 3 seconds to
enter
MENU
. is displayed.
1.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the
MIC TP
menu.
2.
Push the rotary
PUSH
knob (
6
) to
validate.
The current parameter blinks on
LCD.
3.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the type on the microphone
EL
(electret) or
DY
(dynamic).
4.
New Push the rotary
PUSH
knob (
6
) to
validate
. The parameter stops blinking.
a)
Go back to point
1
to
adjust
another function or
b)
Press the
PTT
switch
(
17
) to
validate
and
exit
MENU
. disappears.
5.
If no key is pressed, the unit
exits
MENU
after 10 seconds, disappears in
the display.
Default type of microphone is
EL
(electret)
.
11) PA SETTING
This function allows to
select
the operating mode of Public Address.
Push the rotary
PUSH
knob (
6
) for 3 seconds to
enter
MENU
. is displayed.
1.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the
PA SET
menu.
2.
Push the rotary
PUSH
knob (
6
) to
validate.
The current value blinks on LCD.
3.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the operating mode of the PA :
In
,
OF
or
PA
.
4.
New Push the rotary
PUSH
knob (
6
) to
validate
. The parameter stops blinking.
a)
Go back to point
1
to
adjust
another function or
b)
Press the
PTT
switch
(
17
) to
validate
and
exit
MENU
. disappears.
5.
If no key is pressed, the unit
exits
MENU
after 10 seconds, disappears in
the display.
English
