13
In
: the
modulation of the microphone
is transmitted to the external loud-
speaker connected to jack PA.SP. (
D
). The
received signal
is transmitted to
the internal loudspeaker [or external optional loudspeaker connected to
jack EXT.SP (
C
)].
“PA”
blinks alternately with the modulation mode (AM).
OF
: The reception is no more functional. Only the
modulation of the micro-
phone
is transmitted to the Public Address loudspeaker connected to jack
PA.SP. (
D
).
PA
and
PA
volume level are displayed.
PA
: the
modulation of the microphone
and the
received signal
are transmit-
ted to the Public Address loudspeaker connected to jack PA.SP. (
D
).
PA
MODE:
“PA”
blinks alternately with the modulation mode (AM).
The
MIC GAIN
knob (
4
) to
adjust
the audio level of the mode
PA
.
Default PA setting is:
In
.
See §
PA (Public Address)
page 9.
12) SCAN SKIP
This function allows to
memorize
/
erase
a channel form the
SCAN SKIP
memory
.
1.
Select
then channel to be set.
2.
Push the rotary
PUSH
knob (
6
) for 3 seconds to
enter
MENU
. is displayed.
3.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the
SCAN SKIP
menu.
4.
Push the rotary
PUSH
knob (
6
) to
validate
.
5.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
alternate
between
ON
and
OF
.
6.
New Push the rotary
PUSH
knob (
6
) to
validate
. The parameter stops blinking.
a)
Go back to point
2
to
adjust
another function or
b)
Press the
PTT
switch
(
17
) to
validate
and
exit
MENU
. disappears.
7.
If no key is pressed, the unit
exits
MENU
after 10 seconds, disappears in
the display.
On
memorize the current channel into the
SCAN SKIP memory
. When a
channel is stored in the memory, appears in the display next to the
channel number.
OF
erase the current channel from the
SCAN SKIP memory
, disappears
from the display.
See the §
SKIP
on page 8.
13) RESET
Erase
the scan skip memory or
restore
all factory settings.
Push the rotary
PUSH
knob (
6
) for 3 seconds to
enter
MENU
. is displayed.
1.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
the
RESET
menu.
2.
Push the rotary
PUSH
knob (
6
) to
validate.
SC
or
AL
blinks on LCD.
3.
Turn the rotary
PUSH
knob (
6
) or use
UP
/
DN
buttons (
18
) on the microphone
to
select
SC
or
AL
.
4.
New Push the rotary
PUSH
knob (
6
) to
validate
. The unit
exits
MENU
.
disappears.
5.
If no key is pressed, the unit
exits
MENU
after 10 seconds, disappears in
the display.
SC
erase
all the channels
stored on the
SCAN SKIP memory
. They are now
enabled to be scanned
(see the §
SKIP
page 8).
AL
restore all the factory parameters.
D) FUNCTION WITH PTT SWITCH
1) TALKBACK LEVEL
This function allows to
adjust
the volume level of the
TALKBACK
.
1.
Activate the
TALKBACK
function
(see §
TALKBACK
page 9)
.
2.
Press and hold the
PTT
switch (
17
) then turn the rotary
PUSH
knob (
6
) to
increase
(clockwise) /
decrease
(counterclockwise) the volume level of
the
TALKBACK
from
1
to
9
.
3.
Release the
PTT
switch (
17
).
E) TECHNICAL CHARACTERISTICS
1) GENERAL
- Channels
: 40
- Modulation modes
: AM / FM
- Frequency range
: from 26.965 MHz to 27.405 MHz
- Weather channels
: from162,400 MHz to 162,550 MHz
- Antenna impedance
: 50 ohms
- Power supply
: 13.8 V
- Dimensions
: 6.692 (W) x 6.299 (D) x 2.047 (H) inches
: 170 (W) x 160 (D) x 52 (H) mm
- Weight
: ± 2.43 lbs / 1.1 kg
- Accessories supplied
: 1 microphone electret UP/DOWN with
support, mounting cradle, screws and
fused power cord.
2) TRANSMISSION
- Frequency allowance
: +/- 200 Hz
- Carrier power
: 4 W AM / 4 W FM
- Transmission interference
: inferior to 4 nW (- 54 dBm)
- Audio response
: 300 Hz to 3 KHz
- Emitted power in the adj. channel : inferior to 20 µW
English
